HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Hello,
We are designing a product based on the RAK4630 module that integrates nRF52840 SoC.
Since we are creating a low power consumption and battery operated product...
I am trying to set up the AT library to directly talk to the modem through a uart on the nrf9160DK. But when I enter the commands to test "AT+CFUN?" I just get it echoed back...
I'm working with a Fanstel BT40 module which includes an nRF5340 and nRF21540 FEM. As a starting point I'm using the scan_adv example, which is working out-of-the-box but...
Hi,
I'm using Matter SDK v2.7.0, when I build example light_switch for Board: nrf7002dk_nrf5340_cpuapp with Configuration: prj.conf, I get errors as below:
/opt/nordic...
I have nrf9160 with w5500 ethernet module. I am successfully able to get IP address and connect to mqtt broker created locally on my network. Now I was trying to connect to...
Board: nrf7002 Project: matter_light_blub OS: Kubuntu 22 Toolchains: v2.7.0 SDK: v2.7.0
I have successfully deployed and tested projects that run normally, but when I...
Hi, Iam trying to run c++ code on nrf52840. I got working C code, so i try only change .c to .cpp. I got some errors but most of them are solvable by putting libraries(.h...
I was going through the driver files for CS47L63 and apparently I2C is not supported for some reason. Here is the code block I'm talking about
Is there any explicit reason...
I have successfully managed to incorporate the hard-float build of the library for the nrf52840 into my bare-metal application ( custom hardware with an nrf52840) and have...
LED5 is blinking very fast. no appearance on computer at all. nrfjprog --recover not reconvering, Tried another PC, another cable and no response at all.
I am trying to read the WHO AM I register of an ICM20948 over SPI with nRF52832, but I am getting incorrect values.
I have tried different SPI modes, but none of them work...
Using Zephyr (cf2149caf2) / nrfSDKConnect on a nrf5340DK board.
I need to know how to get a direct stack trace (with file/line numbers if possible for a debug build).
...
Hello Nordic.
I used nrf52832 and nrf52840 by nrf sdk.
But I need to develop nrf5340 now, and I understand I have to use ncs to develop firmware for nrf5340.
I have...
Dear Nordic Community,
I am trying to implement a porting of micro-ROS framework on the nRF52840 chip. As stated in their tutorial , the framework is compatible with the...
