hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi,
In case the FMFU fails or the device gets into some recovery state. Is there a way to get IMEI without enabling the modem library? When the modem is in process of failed...
Hi,
Can you please tell us how to send Hex data using AT#XSENDTO command ?
I am using the "Serial LTE" application. In the old SDK version (v1.6), it was possible to set...
Hello,
I recently saw this post: https://devzone.nordicsemi.com/f/nordic-q-a/71940/low-power-mode-using-saadc-with-ble_app_beacon and I'm interested in the example for measuring...
Hello Kenneth,
I am trying to program the nRF52840 Dongle with the HEX file according to "Programming the nRF52840 Dongle". The dongle is connected to USB port and the LD2...
Hello,
I try to port project from IAR to Segger Studio. I followed the guides for porting projects like this and this . So, I did:
- Imported IAR project to SES with internal...
I am using nrf52833dk and download nRF5_SDK_17.0.2_d674dde when i build the code the code the following error occur
asBuild target 'nrf52840_xxaa' compiling SEGGER_RTT_Syscalls_KEIL...
I have an "old" nRF5340-DK which I use to program an external board I am developing. I have no problem with the J-Link/SWD connection to my external hardware using the J19...
Hello Sir,
I will use Nordic nRF52 series(832 or 840) to develop smart bluetooth device. As I need to store mp3 audio files in external flash and then will play mp3 audio...
Hi,
In our use case we act as a peripheral and a phone is connected. We transmit lots of data using a protocol on top of the Nordic UART Service. All data is sent using...
Hi,
I have two questions as below. Thank you.
1. Oversampling + burst mode only can use on one channel, can't support two or more channel. Is it right?
2. If Q1's answer...
HI,
We have developed our product with nRF52805 chip using its reference design (Dongle).
Can i use QDID ( 138610) for my end product certification for Bluetooth SIG?...
Hello,
for some days now, my modem is unable to connect to the network, it gets stuck in searching and i don't know why?. I am using an eSIM card from iBasis and i am trying...
I'm starting a new project and are looking for a way to sync data and events between threads.
I have found the event manager and Zephyr FIFO, Queues etc.
I can't see any...
I'm using <TWI Scanner> example on nRF52 DK to find my sensor's address.
According to the sensor datasheet, the sensor's address is 0x21. However, < TWI Scanner > finds...
