hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
It continue to give "No device available" when I connected thingy 91 to the nerf connect programmer app. I tried turning on device while keeping SW3 pushed but still not detected...
Hi Team,
We are planning use the crypto libraries for our application, just we want to know which library is best for us in terms of speed and memory consumption,
1. mbed...
Hi, I'm almost finished setting up a development environment for nRF52840 DK on macOS. I used the new Toolchain Manager to install everything, and then imported the "peripheral...
While developing our project using NRF9160 , we encounters a hard fault. The screen shot and the map file is attached. Please help us in understanding what is happening from...
Hi, we are using nRF52832 SAADC in differential mode. We have two channels connected.
Inputs are now configured as differential-N and differential-P (PSELP and PSELN). ...
Dear all:
i have a problem about connect distance. My central device is nRF52840 ，peripherals are nRF52810 device。all device Hardware RF performance are good. But,when my...
Hi In continue to Tzvi Kaplan thread and other threads here related to the PDM, like this one:
devzone.nordicsemi.com/.../single-pdm-microphone-at-higher-pcm-sampling-rate...
Dear Team, SDK - sdk version 15.0.0 IDE - Segger Embedded Studio SOFTDEVICE - s140_nrf52_6.0.0_softdevice We are developing our custom application and it is battery operated...
Hallo,
I want to measure the RSSI of a BLE-beacon. The beacons runs fie, my problem is the other side. I read the thread:
https://devzone.nordicsemi.com/f/nordic-q-a...
Hi,
I am trying to make a project where one Bluetooth chip receives an audio file from mobile and another chip will receive it via serial communication and transmit ahead...
Will the nrf52811 I2C compatibility work with the I2C on the MLX90614 IR sensor. I need to make sure that they will work with each other without issue. Below is the datasheet...
I have DFU OTA application running on 52840 platform on a custom board. SDK v15.3.0. I use SoftDevoce S140 v6.1.1.
Then I need to port it to 52832 platform - SoftDevice...
I have used the NRF52 before, but we got a new need for it to be used with FreeRTOS. Usually I use the RAM_START and RAM_SIZE defines the set up the ram usage for the soft...
