hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi,
I have a problem with floating point types on nrf9160.
I get an exception when I get to a simple floating point assinment:
void f(int i)
{
float x;
x = (float...
Hi everyone!
I'm new using Nordic Semiconductor products, I have a Nordic Thingy 91 running Asset Tracker application by default.
I want to test only specific things first...
I was thinking of using the nordic thingy:91 for monitoring purposes in seismic areas.
To this aim, I would need to have some sensors deployed in the environment which:...
Hi,
I need to use nrf_dfu_settings.c to detect external firmware in Bank 1 during application boot. I also need to use Falsh Data Storage to save application parameters...
Hi All,
I'm working from the Thread CLI example, and I got a network of multiple thread devices that works just fine (they see each other, and can send/receive messages...
Hi there,
I'm trying to do a basic test with the GPIO/NMOS - just trying to turn an LED on and off for now. We're going to be doing this in response to the outcome of an...
Hello,
I'm working on the mqtt_simple sample in zephyr environment for NRF9160 board.
We tested the firmware with 2 sim cards with different packets: IPv4 and IPv6,...
azure_iot_hub_connect does the following check:
connect_client looks like this:
If the embedded return at line 40 of connect_client occurs (as I've seen it do) then...
I noticed on Zephyr docs this:
nRF5340 PDK (preview development kit) is an earlier version of the nRF5340 DK. nRF5340 PDK board is deprecated and is replaced by nRF5340...
Hi Nodic,
I try to add the tx power to both the connection mode and advertisement mode to make it long range available. But when I run the code it fails.
Please check...
Hi.
I do not find the description about I-Cache principles and work algorithm.
I read the part of the documentation "NVMC - Non-volatile memory controller". I think, I...
How can configure NRF_LOG_UART to use UART0 or UART1 for nRF52840? I cant see any configuration which uart NRF_LOG_BACKEND_UART will use
As per spec nRF52840 should have...
Hello,
I want to develop a new IOT product using the NRF52840. My device will be using the MCU with BLE and a very low power sensor.
I want to use a 3.7V one cell battery...
Hi,
I would like to input a data(integer) into the CLI and store the data. How can I do that. I have seen SDK but could not find any function or macro.
If there is any...
Hello, Not sure if this is exactly the same as what is happening in this case , but the issue of an early disconnect when NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 247, can simply be...
