I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hi,
I have a question regarding BLE timeslotting. In my setup I have a master with multiple slaves and equal connection intervals set at 7.5ms. The slaves acquire data that...
Hi,
I am using nRF52 to complement BLE function of MTK7628(they communicate through UART),I've implemented most of the functions.Now I want to add OTA to nRF52, so I use...
I'm trying to combine these 2 examples. I tried adding the uart code:
uint8_t cr;
while (app_uart_get(&cr) != NRF_SUCCESS);
to apps_ble_uart while loop and the whole...
Hi all,
I´m trying to create my first BLE application with segger embedded Studio.
My Hardware is the nRF52833 DK with a sensor connected to dev Board via I2C lines...
Hi, there in inconsistent data about the number of UARTs in the nRF5340 OPS v0.5.1:
- Page ii (nRF5340 features) states "Up to 2x UART (CTS/RTS) with EasyDMA" for the application...
Hello.
I'am new to developing with The Thingy 52 and just trying out simple things. I wanted to see if i could toggle/set one of the pins high from the code but havent had...
Dears,
I'm trying to run the mbedtls library with thread safety with the freertos, already defined MBEDTLS_THREADING_C and MBEDTLS_THREADING_ALT in the user_mbedtls_config...
I have never used the GPIOs near the RF pin (GPIO 22, 23, 24), until my latest project, which I needed to due to pin limitations. It is normal for pins adjacent to RF outputs...
Hi.
I try to test using ble pc-drivce C library & 52840 dongle on pc.
except custom service. everything is fine.
under below is custom service pic.
...
This seems to be a recurring question. I suspect the Wireshark/nrf-Sniffer setup is delicate enough that minor changes/upgrades in any of the components causes a problem....
nrf52832 , SDK_V15.3 , ble_app_uart sample code , data communication problem.
Hello there...
I use the SDK V15.2, ble_app_uart sample code, on the nrf52832
seems the...
Hello,
Currently working with Segger 4.42 and SDK 15.0
I've searched around the devzone on doing a passkey connection between my server and central.
I've used the ble_app_gls...
Hi, I'm having trouble pairing with Android devices using the SDK's ble_app_gls example, when I try to pairing with any andoid device it throws the following error "couldn...
