hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi,
I am using nRF54L15 DK and nRF21540 EK together. I am using the GPIO FEM mode. Below is my projconfig:
I notice that I cannot use 21540 EK in 54L15, the overlay...
Hi,
I am trying to pull up P0.08 as an enable pin for this switch TPS7A0518
I use the following code and verified on development board
However, when I move to...
Hi, we have a product in production and we are using the HWID which is accessible via this API https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/libraries/others/hw_id...
Hi Nordic teams,
There is have issue when I compile the V2.9.0. For more details
C:\ncs\v2.9.0\nrf\applications\nrf5340_audio>west build -b nrf5340_audio_dk_nrf5340_cpuapp...
Hi,
I m using SDK 2.9.0. After building and flashing my target board based on nRF5340, I get the above kernal panic error.
This is my .config.
and my prj.conf
Are...
Hello,
I was able many times to download nrf52-ble-image-transfer-demo-master in to nRF52840 DK (PCA100156) and run a mobile application successfully.
Today I downloaded...
Hi ! I'm using nrf52 + SDK 17.1.0.
I found sd_mutex_acquire/ sd_mutex_release, which is great for locking variables that are set/get asynchronously. Next, I'd like to use...
Hi, I'm using nrf52840DK.
I set the selective_auto_ack as true. It should be able to adopt dynamic ack (or ack payload).
I have two data packets, which are ch_pkt and...
Hello,
I try to figure out, why a certain IO pin shows some pattern at startup. After using JLinkExe to set a watchpoint at the configuration register of the pin (GDB was...
I am trying to update my firmware using IOS-nRF-Connect-Device-Manager and am getting an invalidHeaderMagic error when calling: I am using version 1.7.3 (last version to still...
Hello Developers,
I am working with the nRF52833 microcontroller using segger embedded studio with the latest SDK. My issue is that I can configure and use all GPIOs except...
I have browsing this site, no clearly answer found, but,I think someone has done this job before.
My scenario:
.many BLE client (5.0 above);
.BLE clinet will upload...
Hi, We have an application running on the nRF53, and would like to change the BLE MAC address from the default Random Static Address, to a Public Address with a valid Vendor...
I'm studying with PCA10059,trying to build a gateway between BLE peripherals & PC.
For PCA10059 has build-in USB socket,and I will plug them into PC's USB ports at last...
Hi all,
I want to use UART periodically, but because I need to communicate with other standard UART, I cannot use LPUART
I saw that Zephyr's demos all use CONF_SERIAL...
