hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Today I bought a new NRF-PPK2, but compare with my old NRF-PPK2.
For the old and new PPK2, I use the same DUT.
It can't show the same current with my old one? can you...
Hello, We are developing an application with nRF52810 based on nRF Connect SDK V2.4.1. The application is utilizing the BLE connection, particularly the NUS Service (emulation...
Hi,
In our project, we are planning to use the nRF9160 for both LTE-M and Wi-Fi. Thus, we have connected the nRF9160-DK to the nRF7002-EK in the developing phase as we read...
Greetings developers,
I am using nrf connect sdk 2.7.0 with nrf52811 soc. 1) present situation:
My application sequential in nature and does not have multiple thread...
Hi,
I am failing to build any of the Matter, Thread or Zigbee for nrf52840dk with the following failure.
I successfully build a blinky and bluetooth app, so my tool chain...
I am trying to use fstorage with the sd backend (SDK 14.0.0). My issue is that, after successfully calling nrf_fstorage_write, the callback I registered using
just never...
Hello,
I'm developing a program on a NRF52840 DK in the SEGGER Embedded Studio IDE that outputs a PWM signal when a Bluetooth Mesh GenericOnOff signal is recieved.
I got...
Anyone knows why I'm getting this result? I'm building the application using sysbuild and flashing normally on nrf52840dk. I tried both following all the steps in the lesson...
Hi,
i am trying to create an Indoor Positioning System with the nRF54L15.
Currently i am able to connect 1 initiator to multiple reflectors simultaneously,
When...
i have used same Serial_lte_modem sample code from nordic toolchain 2.6.0 , Enabled shell just by setting config macro
CONFIG_SHELL=y and SLM uart loging is by default...
Hello,
I'm trying to run the NVS example on the NRF9160DK rev 1.1.3 with the on-board MX25R6435F external flash memory.
The sample runs OK as nrf9160dk/nrf9160 but the...
I'm working with the Matter Template example and creating a sensor monitoring device on the nRF52840 platform, and I'm developing on a Windows environment with SDK 2.9.0....
hi support team,
i have one problem for 54l15+7002 in ncs2.9.0
I am afraid that I need your help.
I was porting MQTT demo and PERIPHERAL_UART demo together and want...
I have a nRF9151 currently set up to observe a CoAP resource on my server. The initial GET request works, and if I respond with new updates from the server (within a few seconds...
Hi, guys. I encountered some software issues while using VS Code for development on the nRF5340 DK. During the build configuration, the code reports an error saying it cannot...
