I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi. I have a working IAR project based on the nrf52 SDK \nordic\examples\ble_peripheral\ble_app_uart. i am attempting to port the project to ARMGCC using VSCode. I am at a...
Hello. I try to create a remote control for GoPro using nrf52 ble.
Using sdk 17.1 examples I can connect to GoPro and try to get a list of UUIDs. But I only get one UUID...
Hello
I'm using the settings partition to store user configuration data. I know that the BLE stack also uses it — particularly for storing bonding information — but I don...
Hello Everyone,
I am using a nrf54l15 for my current project and ran into some discrepancies within the documentation provided for the processor.
Even the AI chat bot...
Hey I was working on starting sample code of wifi in ncs v2.6.1. When I added the correct ssid but wrong password in the prj.conf to check the status of the connection failure...
Hi there,
I am currently trying to use device sleep modes with Matter. Nevertheless, once I add "CONFIG_PM_DEVICE_RUNTIME=y" to my prj.conf, the main-method is not longer...
Hi, I have been experimenting with the Direct Test Mode program. I am using an nRF9160 DK, specifically the bluetooth chip nRF52840.
The Direct Test Mode is not officially...
Hi,
I am using sensor observer sample to get the data from sensor sample. However, I notice the power consuption is too high. I have look thourgh the forum and found this...
Hi,
I`m designing the schematic, and met some problems, could you please give me some guidance?
Does the pin only supports the described peripheral function and not...
Hello, I am working with a Bluetooth Mesh network where a master node (antenna) is in charge of setting up and managing the network of nodes. This master node also deploys...
Hello,
I am currently using CADENCE for schematic design and have used Nordic's nRF9151 and nRF54L15 chips. However, the reference materials downloaded from Nordic's official...
Hello,
already found a description in the Tech Docs, how to bring the external memory into deep sleep on QSPI interface: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hello support,
For our project we have an integration with Memfault for metrics, coredumps and log files.
We are currently developing in NRF 2.7.0 on a nrf9160 chip. ...
Hi,
when i try making a new connection with a new device using my for loop (reconnecting using the adresses that i stored in an array), i sometimes can get a warning which...
I'm trying to use both uart0 and uart1 on nrf5340 (only App core) but I get this message: UART_RX_BUF_REQUEST event, but not the error. I have also tried to pass another buffer...
