I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
This question relates to using zcbor .
Basically I have the following.
I got The contents of FRAME - 00, 00, 00, 02, 00, 01, 01, 00, b0, 06, But I was expecting 00...
Hello,
we want to send a continous carrier with nrf9151 on dect-nr+ on a specific channel.
With bluetooth there is a testing option in nrfconnect tool.
Is there any...
Hi I would like some advice on where to start learning Nordic BLE?
All I could find by searching was advice from 6-9 years ago, I think today they are not relevant, because...
hello,
I'm doing a power consumption test, but I'm not sure which project to use to test the power consumption.I tried the "peripheral_lbs" download with NCS version 2.8...
My setup: SDK version: 2.5.0.v Modem version: 1.3.0. I am using MQTT to subscribe to a topic, for example, the LED state. The plan is t o set the LED state on the server side...
Hi,
The SDK version I am using is 2.6.1 and the example is "matter lock".
I wrote the following configuration into \child_image\mcuboot\prj.conf.
And add the code...
Hello, thanks for reading and happy holidays!
We are using an nrf5340dk, with zephyr and SDK 2.5.0.
We seem to have two undesired behaviors from MCUBoot immediately after...
Can,t flash nRF52832 custom board using nrf connect vscode extension im trwing to use nRFconnect for my project, im using fade_led from example and got this error
i try...
Hi everyone, I have a problem when I tried to configure UART ( baudrate, parity, data_bits, stop_bits, flow_ctrl). I upload my project:
#include "myuart.h"
#include...
Hi,
I want to use nRF9160's internal RTC. I coded it but did not get the real time correctly.
SDK: 2.5.0
IDE: vs code
board: nRF9160dk
Best regards,
Liza
I'm going through the Academy courses and somewhere around Lesson 3, I could no longer flash firmware to the nrf52840 DK.
I browsed the forum and found some notes around...
nrf connect for desktop nrf54l15 device not detected by bluetooth le app
log:
12:18:38.872
Using nrf-device-lib-js version: 0.4.4
12:18:38.872
Using nrf-device...
Hi,
in Cellular Iot Fundamentals there is in lesson 4 an exercise to move to MQTT with TLS.
As I used MQTT helper library, I wonder if it is enough to modify the structure...
We had an issue with the FDS such that if the device lost power in the ~50ms window after bonding was carried out, the FDS would take longer to initialise when power was restored...
