Has anyone used a graphics library like emWin or TouchGfx on nRF52?
www.segger.com/emwin.html
http://touchgfx.com/en/
I do not see any posts on either forums or here...
Hello,
We can not convert Altium File to DipTrace or Eagle File. We need those files asap. I'd be thankful if you could help me in that issue.
Thank you
We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
Hello,
I am having nRF 52840 SDK for which I am able to control leds of sdk using ble app blinky example through android mobile.
Mean while, in nRF mesh provisioner example...
I'm having a bit trouble here getting migrated to LPUART on a working nRF9160 <> HCI BLE on nRF52 (On the Thingy91). As far as I can tell my .conf and .overlay files are what...
Hello,
I've run into a problem, which seems at least to be similar to that described in another thread . In short, if I set up a counter with CC[n] and start it, a COMPARE...
Hi,
I would like to store important information (few MAC addresses) in flash memory at manufacturing stage. Then my program will be able to read these information thanks...
Hi ,
My environment:
nrf5340 DK board
nrf connect SDK v1.5.0
segger Studio IDE
I would like to establish communication from application core to network core...
Hello I want to make a python script that allows sniffing of 802.15.4 packets (nRF52840), The module exposes an API that allows starting and stopping the capture. I installed...
I am using windows 10, nrfConnect 5340, and the NRF5340DK.
I was searching for an example of how to configure and use the usart/uart 0 port as a 2 way interupt based serial...
Similar to this problem , I cannot open the serial let modem example for nrf9160dk_ns. I tried moving my nrf install to the root but did not help. I am using Windows 10. The...
I want to read the acceleration sensor value using the example of the ble-hid-keyboard, but if I let you read the acceleration sensor value, Bluetooth will be cut off. Can...
Hello, I am having trouble understanding the flashing process of an nrf52840. I have programmed a simple flashing example with the nRF5 SDK. I compiled the project using make...
Hi Nordic,
I am using the two nrf52840 units to test adv and scanning in a pair for the development. I am using BLE_GAP_PHY_CODED for both scan and advertisement. But...
Hi,
We have recently switched from using nrf52810 to nrf52840. Firmware porting went well until we tried using the BLE on nrf52840. No matter what we try the BLE will not...
Hi, dear Nordic
1) Could nRF52810 Serial Debug Pin be used as GPIO/I2C?
2) Some post mentions using the external circuit, so that the 2 Serial Wire Debug pins can be used...
Hello
We have developped a product with the nRF52832. Due to space restrictions we couldn't use the PCB antenna design from the nRF 52DK. We used an Johanson chip antenna...
nRF5340 datasheet page 2 states that the TX power is configurable from -20dBm to +3dBm. But later on in TX power section, it states the power level can go down to -40dBm....
