I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello,
While working with a bare metal (no SoftDevice or OS) test application to prove code functionalities, I ran out in a weird behaviour that I cannot explain.
I'm...
Hi,
I started to implement the nrf ppm driver into my application. It is a smart connected grand light.
My goal is to smoothly fade the connected power LEDs on, hold for...
Hello,
So I have the following setup. I have an nrf9160 DK board. With the following hardware.
A base shield: https://www.reichelt.com/ch/de/arduino-shield-base-shield...
Hello,
I am using the att_mtu_max_throughput example from SDK 15. I am using an nRF52 as tester and nRF52840 DK as receiver.
I have modified the example slightly so that...
Hi Noridc guys
recently I got some issues about how to know device network state. then I found there was a issue in zb_bdb_is_factory_new() API.
first, i formed a network...
Hi,
I have a problem of crash device after trying to connect my device to the PC via NFC.
The issue is very rare.
I think that the issue occurs because of an assert...
Hello,
I'm currently testing the bootloader with nrf52832 DK on SDK16.0.0 with Segger Embedded Studio. I followed the guide provided in this link https://devzone.nordicsemi...
Hi,
My project is based on SDK15.3 with NRF52840. I have referred to the "writable_ndef_msg" example to read/write the emulated NFC tag successfully. And I can get back...
Hai ,
In my application i should connect parallel connection and peripheral and central part connections simultaneously.
for this i developed from hrs_relay example .in...
Hello,
I'm trying to program a nRF52840 Dongle with the thread MTD client example by using nRF Connect but I get an error saying I need to add a SoftDevice. I thought...
Hello, I am new to NRF52. I have setup a project under Embitz ide. I can compile GPIO toggle code and program the the code. However when I try an transmit example github.com...
I have 100 samples of string data (Ex: AABBCCDDEEFF:1592636399:1592636399 ) . I am using the flash_fds module. Also, I want to read the read all the samples at once. I am...
Hi,
I am developing the 'buttonless dfu' to the 'hrs freertos' using the SDK v15.3.0.
However, after I compiled the modified code and loaded to the target broad, I got...
Hi
In ble_stack_init(), err_code = softdevice_enable(&ble_enable_params); err_code = sd_ble_enable(p_ble_enable_params, &app_ram_base); err_code is 4.
I use nrf51822 in...
Hi,
I got a nrf5340 pdk, and I download demo Peripheral_Heart_Rate into board, load peripheral_hr.hex into app_core and load hci_open_amp.hex into net_core. it running ok...