Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
We are seeing about 500 uA in sleep mode and we expect to see under 2 uA. We are using an nRF52810 on a BMD-330 module on SDK 16.0.0.
Here's the relevant code...
nrf_pwr_mgmt_run...
Hello all!
How can I get the current count of a timer without stopping it?
Right now I'm doing like this:
_timer_base->TASKS_CAPTURE[channel] = 1; uint32_t counter...
Hi,
I am no programmer, but I wanted to try the Wake-on-NFC example on the 52840 dongle (I soldered an NFC flex on pins P0.09 and P0.10). I have downloaded SES and nRF SDK...
I want to connect heart rate sensor and bike power sensor together. I config channel 0 for heart rate sensor,and channel 1 for bike power sensor. Ant work well when both sensors...
I've just tried to compile and run the stock lpcomp example on two different computers, targetting an off-the-shelf 52840 dev board. It compiles, and starts fine, but doesn...
Hello,
I am creating an application that counts the number of times the button is pressed (Every high to low transition).
I am using GPIOTE to sense the high-to-low events...
Hello,
I am considering redistributing the SDK source code. I also saw the following, but hasn't it changed?
devzone.nordicsemi.com/.../32969
【SDK：15.3】
Hi,
How can I understand what all Errata's are applicable to softdevice and are taken care of?
For my application I am aware of the modules/peripherals being used and...
Hi,
I noticed there is no SWO support mentioned in Product Specification 1.1 for nRF9160. But since the architecture seems similar to the nRF52/nRF53 that have SWO under...
I have been interfacing with the Macronix external flash via the nfrx_qspi library for logging. While I am able to use nrfx_qspi_read() to obtain my log data, I am also able...
PM_MCUBOOT_STORAGE_ADDRESS and PM_MCUBOOT_STORAGE_ID seem to be no longer defined as of SDK1.2. As per the discussion here , I tried using DT_FLASH_AREA_STORAGE_OFFSET which...
Using nRF52811, Segger SES, and SDK 16.0, I have some times that seem to be off by ~2X.
I'm timing by setting a gpio before and after the event and capturing with a scope...
Hi
Referring to
https://devzone.nordicsemi.com/f/nordic-q-a/58652/additional-questions-to-nrf52832-errata-220-clearification/238659#238659
From the above post, the...
I am new to the nRF9160dk board. I have been able to compile and run some of the sample programs. I am now looking to have a simple program to talk to external uarts 0 and...
