We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Hey, i want change the simple_on_off model a little bit, so the server return an byte array to the client get_message, can you say me how to include vendor specific model...
If nrf_gzll_ok_to_add_packet_to_tx_fifo() returns false and nrf_gzll_get_error_code() returns nothing, what does this mean?
Facing this a lot when trying to change channels...
Hello,
I was trying to perform DFU over mesh. My setup was as followings:
7 nrf52832 Devies. One of them is connected to my laptop.
I programmed those according to this...
Hello,
I'm using the nRF51422 with a dfu dual bank bootloader with SDK 11. I can programm the uController with the Softdevice and the bootloader and afterwards load successfully...
Hello, I'm trying to add a Peer Manager functionality to the Mesh Provisioner application.
I'm using nRF52832 devkit, Segger Embedded Studio, nRF5 SDK for Mesh 2.0.0 and...
Hi,
for some reason I cant debug in Keil, the program doesnt stop in main.
I also have NRF_LOG enabled, but nothing appears on RTT.
What could I do?
Thanks!
My environment is:
Windows 7
JLink Plus v9.3
IAR EWARM 8.30.1
SDK 15.0.0
Softdevice S132.
My hardware is a custom board with a Rigaldo BMD300 module (contains...
Hello,
I'm trying to modify the dfu_dual_bank_ble_s130_pca10028 bootloader so my device would start with the application and after a signal (with the button) it should...
I have an application where a unit contains a nrf52840 and will act as a central device, collect the data from peripheral device and store into the onboard memory. Upon the...
Hello,
I'm seeing higher than expected power consumption when running an RTC peripheral using LFXO as the LFCLK source compared to using the internal RC. Specifically, I...
Hi, to repeat the problem, you need to press button 3 and then button 2 on the board with an example of dimming_client, after that the board with dimming_server stops responding...
Question 1 :
I write 512 words to flash but only can get some value right .and some value was wrong.
I used fs_store( &one_min_data,
(uint32_t *)(FLASH_DATA_ADRR), ...
Hi All,
I am a newbie to Nordic SDK and Mesh SDK.
I am trying to generate my On/Off application using the Nordic Mesh SDK (v2.0.1).
Here is my setup.
1) Have Mesh...
I am in the progress of updating to nRF5_SDK 15.2.0 from 15.0.0, project on nRF52840/Segger Embedded Studio.
I have NRF_LOG_FILTERS_ENABLED defined since I want to log less...
