Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello,
I would like to add a costom cluster,controlled by custom App.I add cluster xml file,and run zap_regen_all.py to generate corresponding code.Everything is ok, the...
I am testing the current consumption of SIM cards with PPK2.
When PPK2 is connected to VCC ( voltage 1.8 v or 3 v ), the PPK2 can display the current properly ( around 9...
Hello I need to read the current mesh IV index of a provisioned node. Found 2 structures with the iv_index field : struct bt_mesh_cdb bt_mesh_cdb and struct bt_mesh_net bt_mesh...
When I package the firmware with nrfutil v7.12.0 version， I pack with a command like this
I got the right app.zip，manifest file
My question is: In nrfutilV7.12.0,...
I am planning to perform encryption using the CC312 accelerator on the nRF5340. I would like to evaluate the power consumption when using the accelerator.
My approach is...
Hi,
I am using nRF5340 DK and nRF SDK V.2.6.1 for my project
I clone the project from git and try to build the project using custom board but it is giving the cmake error...
1. When adding CONFIG_PSA_CRYPTO_DRIVER_CC3XX=y to the configuration as shown in the diagram, does it enable the use of the CC310 accelerator?
2. My understanding is...
We are making ZigBee product. The base we have took is from nrf connect sdk samples light_switch and coordniator example. everything works fine but we need to keep some information...
"I am working on a project involving Matter over Thread using the nRF52840 development kits. My goal is to pair and communicate between the light_bulb and light_switch Matter...
Dear Devzone,
I'm using 52832，SDK 17.0，keil.
What apis should I call if I want to enter the bootloader mode from my app? For example, I receive a message from a serial...
Hi,
I'm trying to do DFU on a custom designed Bluetooth peripheral device using nrf connect for mobile application. I can able to perform DFU successfully is some mobile...
I am working on RTOS that does not have WiFi driver for nordic wifi chips. I would like to port this driver to that RTOS.
In the documentation there is a mention of platform...
Hello everyone,
I’m facing an issue with step-by-step debugging in VSCode using the ARM GCC compiler with an nRF52811 microcontroller and Nordic’s SDK 17.1.
Here are the...
nRF Connect SDK 2.6.1 + nRF52832
I can't get the execution of shell commands from mcumgr over SMP to work.
Here is my prj.conf :
I registered some custom shell commands...
I have an application I have been developing in NCS v2.3.0. I'm trying now to updata to v2.4.0.
The application targets NRF5340.
It uses NSIB (b0/b0n) and for the application...
