Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hi, I am trying to get the voltage level of the battery using the AT_command AT%XVBAT which I tested using the at_client sample. I tried integrating it with my current code...
From looking at the code when a message is posted to "all-nodes" fixed group address of 0xFFFF it does not route. I was unable to find this behavior specified anywhere in...
Hi forum,
I am working on nrf52832, using sdk 15.0.0. I want to send the data(command) from esp32 to nRF52832 through Rx ,Tx . I have done connections rx,tx,gnd . I can...
Hi,
We are developing our stack with soft device using nRF52840 as the Controller and have the below queries
1. How to configure a static random BDADDR which will remain...
The error is
CMake Error at ../../../cmake/extensions.cmake:416 (add_library):
No SOURCES given to target: drivers__spi
This similar to
https://devzone.nordicsemi...
Hello everyone,
Hello everyone, I am a beginner in programming with OS based systems. I would like to get more into development with the Zephyr based NCS. For now, I want...
Hello!
I try to run FatFS example (SD card example, pca10040) from nRF5 SDK on my nrf52832 (ebyte e73) with microSD card with no success. No matter what I'm still getting...
Hi,
I am trying to get the time and UNIX time after LTE connected. but getting 0 only.
please log
date_time_update() function does not support in SDK 1.4.2 so I...
Hi,
In "nRF52832 Product Specification v1.4, it recommends 32MHz with 40ppm as below:
as the question mentioned above, can I use one with 10ppm?
thanks
best regards...
Hi,
I am getting assertion failed error when putting the device in System off. Could you please help me understand why?
Below in the code where the error happens:
...
I'm working on modifying the ble_app_uart pca10040_s132 to send strings stored in flash memory over BLE to the nRF connect app on an iphone. From what I understand the uart_event_handle...
Hi There,
I m trying to use the xxxx\SDK's\nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\peripheral\spi with the nRF52480 Dongle and I already had applied the...
Greetings
I have an NRF51422 QFAAEO running S210 Soft Device version 3.0.
I have written a Bootloader application that uses Ant-FS as the upload mechanism. During testing...
Hello everyone,
is it normal behaviour to lose data on UART reception when BLE scanning and advertising both are active?
So far I didn't lose serial data if I just run...
hi all.
I am trying to change number of data packets in one time interval.
I don't know the senario to change it.
For first step I wrote this code to change the quee...
