VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Dear Sirs
We are planning to have our end product certified by FCC and CE. It uses the nrF52840 SOC directly on our PCB. This has the following QDID : 124988.
We have...
I am using cjmcu 8223 board for my project so for uploading program I brought a ST-link V2 pen drive like device but I can't able to detect the board on the ST-link software...
Hi
I am currently evaluating a 52840-DK (from 2017 I believe) and several 52840 dongles (ordered very recently). I managed to successfully run the light/switch mesh example...
Hello,
I'm trying to port the radio synchronization to a nRF5340. For this i need to use a DPPI group that clear a timer and disable itself for doing the task only 1 time...
I'm getting an undocumented status value back from nrfjprog when I try to program my dev board:
ERROR: command exited with status 3221225477 : nrfjprog --program C:/mdsg...
Hi,
I'm new to Nordic tools and am stuck on getting all the pieces in place. I have:
Mac OS 10.14.6
nRF Connect v3.6.1 Getting Started Assistant
Python 3.6.3
All...
Hey Guys,
Transferring emulated project
Transferring an emulated project to the nRF52810 SoC,
If you have developed your application using the emulated project...
Hello,
I am trying to setup a Project with nrf25840 by using the nRF IEEE 802.15.4 radio driver in multiprotocol mode with ble. ( https://github.com/NordicSemiconductor...
Hii guys ,
I have a customised nrf module based on nrf52810 . I have dumped ble_app_beacon code and it works fine but when i dump ble_app_uart example code then i am not...
Hi
I have a question about peers deleting.
It is saying in documentation about pm_peer_delete:
"Warning Use this function only when not connected to or connectable for...
hi Support team,
I have one problem with window7 system both 32 bit and 64 bit, that the usb cdc driver can not be verified by windows, that software signature is not right...
hi support team,
customer has one question about TWI electricity. in the IIC spec the "tLow " should be more than 1.3 us
however, our chip interface TWI timing " tLow...
Overlapping segments detected at address 520192.ERROR: The hex files cannot be merged since there are conflicts.
should be
Overlapping segments detected at address 0x...
I’m obviously missing something from the information I’ve gathered with respect to designing a co-planar waveguide, PCB 50 Ohm transmission line. The calculations I get differ...
