I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
Hello,
I am using nrf52832 with PCA10040 and SDK15.1 along with a temperature sensor MAX30205. So far I can write, but I am realizing that I cannot read the second byte...
Hi, I'm using the nRF52840 SDK15.2.0 I'd like to get data from a digital microphone via a PDM interface. The teansfer data to speaker via a I2S interface.
Here is my problem...
I use the SES ver 4.12 with embOS of Segger.
It happened to me all the time.
I take an example from Nordic. I rebuild it with no warning. Then I take and add my files...
During the firmware running, there will be a HardFault_Handler error occasionally.
Is there any way to locate the error source?
Is there any good way to catch the hardware...
Hello. I have a problem with enabling nrfx module. I get this error during prohect compilation: 'NRFX_TWI0_INST_IDX' undeclared here (not in a function); did you mean 'NRFX_TWI_INSTANCE...
Hi,
I'd like to set 3 nrf52840-DK in the following way :
One device acts as central
2 devices acts as peripheral
I'd like the central to be connected to both peripherals...
I have custom board with nrf 52832. I am using SDK 12.3.0. and soft devices s132 V3.0.0 to transmit advertising packets with advertising interval 1s. I have written simple...
I already have a few devices in the field, and I'm curious if it is possible to occasionally update the signing key (e.g. to upgrade key, or compromised key, etc). If not...
Hello, I want to establish a connection between NRF52832 IC and ESP32 Module.
I implemented BLE on ESP 32 and achieved communication between Nordic Mobile app and ESP32...
Hi,
I am trying to used the WINC1500 Wifi module with the nRF9160 DK but I am not getting any data back from the module.
I am using the module
https://www.microchip...
Dear Nordic Support,
I follow this SAADC example to calibrate the SAADC every SAADC_CALIBRATION_INTERVAL.
However, whenever the function nrfx_saadc_abort() is called...
I am running into a strange issue. I want the bootloader to start automatically when I power on the device and then start the application if there is no activity after 30...
Hi,
If I want compiler my project at specified locate, the only thing tat I need to do is following image? Is it right?
After I program this program into address 0x0001D000...
I am trying to make PN7150 work with nRF52840 using TWI Communication.
Problem : PN7150 gets detected with I2C scanner example when using Adafruit Bootloader and programmed...
When I run "pc-ble-driver-py/pc_ble_driver_py/examples/serial_port_enum.py" on armv5tejl GNU/Linux 4.2.6+ (32 bit) connected with NRF52 DK, it is throwing an exception
...
