Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear all,
I am using SES, I have an application that relies on a softdevice. For it I developed a custom bootloader that DOES NOT rely on the softdevice and only transfers...
Hello, Nordic! I'm developing with a nRF52832, a bmi sensor and SES. I am starting with the BMI160 libraries on github and encountered some problems with the call of the i2c...
I am trying to implement a simple matrix 4X4 keypad. I have an issue in enabling gpiote events. I disable gpiote events when there is a row event and i scan the keys by turining...
Hello,
We were wondering under what conditions the SIM will reset. AT commands will give us activity on the SIM_CLK and and SIM_IO lines, we are looking to see activity...
Hii,
I have two question regarding advertising and connection
1. Is there any way to hide my peripherals advertising from any other central scanner .
2. Is it possible...
Hi
I did test two sample code with nrf52DK kit in segger embedded studio. with sdk ,nRF5_SDK_15.3.0_59ac345
1) ble_app_uart (I connect one sensor with UART,I did some...
Hi,
we are progress of designing custom board using nRF9160.
By reading nRF documentation, my understanding is GPS circuit in Dev kit is unstable/nonperforming.
Could...
I'm compiling a custom application using the CMake scripts in the nRF mesh SDK. The first time I flash to the nRF52832 a SIGTRAP occurs on sd_softdevice_enable. I cannot continue...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10
When I run the demo of b le_app_hrs on my development board,I use nrf connect app to...
SDK 13, softdevice 132
function fds_register results FDS_SUCCESS
by calling the function fds_init debugger stops, see comment in function below, and i see "unknown...
Hi
I'm a total beginner here and I have the gyroscope sensor LSM6DS3 and I have the nRF52 DK
I want to read the sensor's data via I2C (i.e. using SDA and SCL pins) using...
Hello.
This is becoming a very serious issue for me. When I program the nrf52840 dongle and when I switches on the power, it automatically goes into bootloader mode, means...
I purchased a sparkfun breakout board ( https://learn.sparkfun.com/tutorials/nrf52832-breakout-board-hookup-guide and schematic https://cdn.sparkfun.com/assets/learn_tutorials...
I'm compiling a custom application using the CMake scripts in the nRF mesh SDK. When I debug the application, even though the debugger is working – I can pause execution ...
I am trying to modify the central / peripheral relay example to not use the HRM and RSCS services and to use my own custom service instead.
I am following this tutorial...
