Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to get a Bluetooth interface (Bluefruit) to the Nordic BLE softdevice under NuttX. Right now it's very unstable. It will work occasionally for 90 seconds and then...
Hello,
When trying to connect to our custom board, it ends in Time out after 5 seconds.
On the board, I put the simple Nordic_Blinky example (\examples\ble_peripheral...
For the custom_ble_service_example , trying to change the service used in the example to a Bluetooth SIG service.
Original is: CUSTOM_SERVICE_UUID_BASE f364adc9-b000-4042...
Quick question: when will the nRF52840 DK available? On the nRF52840 DK page, there is a recommendation to avoid the PDK:
"The nRF52840 replaces the nRF52840 PDK which is...
I have the super typical problem of needing long data transfer greater than the 20 byte MTU size.
I have a basic protocol that has the total length of a long message coming...
Hello everyone, I am very new to nRF52832 Development Kit and was testing some examples to get familiar with this kit, however i encountered an issue while testing the ble_app_uart...
Hello,
We are having problems with Gazell pairing. Both the host and the device are using the Gazell stack from the nRFgo SDK 2.3.0.10040 ported to run on an Atmel SAMD20J18...
sdk 15.0, SES
In CMSIS checked NRFX_TWI_ENABLED, and checked and unchecked TWI_ENABLED to no avail.
Looked at driver API , but with no specific hint.
Looked for other...
Hi Engineers !
We are going to implement AES CRYPT/DECRYPT Protocol over BLE to add some additional protection against HACKing with use of HW " 6.6 CRYPTOCELL" the MODULE...
Hi, I want to use a couple of 0805 resistors, hook them up in tandem to 220V AC power source, and then do some zero-crossing detection.
I know I know, this totally isn't...
Is it possible to use the Segger SystemView software with the NRF52832? When attempting to use SystemView, I get an error "RTT Control Block not found". It's possible to enter...
Hi,
I can't find information what shape of spectrum I should expect from test mode (CONT_WAVE = 1, PLL_LOCK = 1). At the moment I get main spike with smaller symmetrical...
I'm running into an issue when trying to use the timeslot API for advertising while concurrently scanning. Scanning is using a 100 ms interval with 50 ms window and initialized...
Hi!
I have created a project for nRF52 DK in Segger Embedded Stuido. I wanted to creat it for nRF51 but there was no eamples to start from in the sdk that supports pca10030...
