Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Hi,
I am new to Nordic product and I have NRF52 DK. I have started reading this document
www.nordicsemi.com/.../Getting-started-with-the-nRF52-Development-Kit
However...
Hi,
I am trying to use the BLE v4.2 extended data length on the NRF51822 but the S130 doesn't seem to support it. Please can anyone let me know if it is supported with...
Hi,
I am trying to measure (and reduce) the current consumption of my board. I am using nrf52832 (64K RAM) for my development. The RAM layout is as follows: RAM (rwx) : ORIGIN...
Hello,
Is there any way to mitigate delay of redirecting interrupts from softdevice to application? Using nRF51 with S130 there is ~2us delay even with SoftDevice disabled...
Hello!
I have nRF52 DK and 1 custom designed nrf52832 PCB.
Is it possible to use the one of the nRF52 DK as the BLE dongle and run the ble_app_uart example code on my...
I am developing code to nrf52 and i'm using a sdcard with the adafruit MicroSD card breakout board.
When the sd card has no partitions I'm using the fdisk function (from...
Hi Hi, I am new and I am playing with
nRF5_SDK_12.2.0_f012efa examples in Keil
for some reason I need to use hex file. The files which is generate from those examples...
Hi. I have two codebases here:
A peripheral application on an nRF51822 using SDK 12.2.0, SD 130. It has a vendor-specific service with a characteristic that is write...
Hi,
I am having problem in installing Softwares and drivers required for NRF52.
Please kindly tell me step by step instructions of what software is needed to be install...
I am in the process of getting some nRF52832 based proto units and plan to use the nRF52 DK to load the code and maybe do some external debugging. I will be using P19 (debug...
Hi,
I'm new to embedded development and am trying to interface a 24-bit MEMS microphone (Invensense ICS-43432) using I2S with nRF52 Dev board (PCA10040, V 0.9.0, 2015.39...
Hi,
Basically i want my nRF52 DK should be able to transmit data to connected android device and also be able to receive data from android,data is kind of logs.
hi,
I would like to do some code profiling and measure execution time.
What is a lowest possible resolution for the counter is possible to achieve and how?
I am currently...
