I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
In the cs_de.c, we have an IQ pair extracted from remote_pct and local_pct. Assuming this code runs on initiator (where the ranging is done), and remote/local stands for reflector...
I tried to use NRF_SOCK_RAW and NRF_IPPROTO_RAW to create socket, but found `modem fault`!
//this is my wrapper
socket_create ( true , AF_INET , SOCK_RAW , IPPROTO_RAW...
Hi, I very much doubt this is a SoftDevice issue but sticking it out there as an Apple dev asked me. Short story is I have users in production using an App connecting to NRF52810...
Hello Nordic Team,
I am using nRF5340 DK as a debugger/programmer to develop firmware for the Fanstel EV-WT02C40C module. My goal is to do i2c communication between Renesas...
Good morning, I have built and flashed the l2-e1 exercise on both the nRF5340DK and the nRF54L15DK. When the nRF54L15DK boots, the following output is displayed in the terminal...
Hi,
I’m working on nRF54LM20A and trying to configure the internal capacitors for the 32.768 kHz crystal (LFXO) using the factory trim values in FICR.
According to the...
Hello, read through the documentation about the SAADC and found the TRIM.LINCALCOEFF[n] register. ADC-linearity is important in the project I'm involved in... Seems that the...
Using nrf connect SDK 2.5.0
The nrf device is an L2CAP CoC server. I am using an RPi 4 to test with. The application is for transferring data through UART to another chip...
Greetings!
We have been using an nRF52840 Development Kit for a while now and have been performing FW updates OTA (between the same 3 FW images, cycling and updating between...
I am still on the learning curve of nRF Cloud (and the nRF9151 in general) and am trying to add A-GPS to a project.
Using nRF Connect SDK and Toolchain 3.1.1, I cannot add...
I am using the nRF Connect for Visual Studio Code Add-In running with the nRF Connect 2.5.0 toolchain and was trying to implement the application versioning on a nRF5340 DK...
Hi,
I am working on a project which uses nRF5 sdk v17.1.0 & mbedtls v 2.2.8.2. Now i ma planning to make some changes in application code and re release it. My question...
There appear to be mistakes in haptics_handler.c it appears to be using outdated functions / includes in NCS 3.2.1:
The corrections that work for me:
Changes made: ...
I must have the PPK2 data logger running for too long .because now it won't start. I see the currently available space is 0.0 MB, so maybe that's the problem.. I tried to...
