Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi
I have tried to reproduce the 2.7µA current consumption stated in the datasheet. This webinar shows that the UDP sample reaches 2.7µA on the nRF9160 evaluation kit. However...
Hello Nordic! My question probably a simple one but I'm a novice so there's it. I'm looking for a way to get a GPIO port state that was at the moment of GPIOTE event triggering...
Dear Nordic Support
We have an existing Project that uses the nRF9160 SoC and builds with toolchain v2.4.4 and SDK v2.4.4.
The project basically runs with the nRF9160...
Hello,
My DK stop working as programmer suddenly.
the VDD power is normal with 2.9V and the V5.
Try already to power on with reset button hold.
blinking is not Consitency...
Hi Support Team
We meet an issue like the screenshot below when I program nRF52840 chip via the SES.
The SES version is v5.42a.
The J-link we used to program is...
hi:
asset_tracker_v2\src\modules\led_module.c
I only found the file that calls the LEDs, I didn't find the specific initialization and control code? Can you tell me how...
Hello everyone, a pleasure and very grateful to be able to write in this forum.
I am trying to program a Nordic BLE device so that it does not appear in the pairing list...
Hello, I am developing a board using the nRF52840 QFN48 and powering it using a 3.7V single cell LiPo battery. Since the battery voltage is stepped down to 3.3V via an external...
Hi.
I would like con build nrf Connect OT COAP Client and Server on a zephyr 4.0.99 / toolchain: zephyr 0.17.0
I have downloaded nrf sdk 2.9.99
running:
west build...
Testing the RADIO TEXT example on 52811.
1. 52811 is not a supported target - so I must select all targets then the unsupported dts (nrf52840/nrf52811)
2. I add a Build...
Dear Team,
Is it possible to run BIS and PAwR concurrently while using PAST for synchronization? I am using the nRF52840 DK and NCS 2.8.
I managed to start two periodic...
I am working wih \nrf5_sdk_17.1.0_ddde560\examples\802_15_4\wireless_uart\secure\first\
And I want to add app timer to start a peroid works.
unfortunately， this timer...
Hi Q&A
At present, there is no routine found on the Internet about NRF52832 Bluetooth sending more than 6 characters(NKRO)
I used nRF5_SDK_17.1.0， The following is the...
