I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hello,
just recived this kit, I ordered it some time ago but were no stock.
Problem is that software doesn't detect the hardware under "SELECT DEVICE". The device has...
When flashing files from an iOS device I run a lot into data size errors (not always), when using the same files on Android they can be copied without a problem.
It looks...
Hi,
I built a ble_app_buttonless_dfu_pca10040e_s112 project on the nRF52805. However, I cannot receive Bluetooth signal on nRF connect.
I have attached my generated hex...
Hi,
In an application with a nrf52840, we measure the frequency by counting rising edge with PPI linking GPIOTE EVENTS IN and TIMER TASK COUNT
GPIOTE.EVENTS_IN -> PPI...
Hello everyone,
I created my first own layout design and the antenna. Before I order the PCB I hope you guys can review it one time. I tried to get the most informations...
Hi all.
As per subject, I'm unable to follow device using PCA10040.
Everything was set according the latest documentation available ( infocenter.nordicsemi.com/.../nRF_Sniffer_BLE_UG_v4...
To the kind attention of Nordic support team,
we are planning to use nRF5_SDK_17.1.0_ddde560 and nRF52820 for a project. We are interested in using gzp gzll library compiled...
Hello
I'm working on a project inspired by the ble_thread_dyn_mtd_coap_cli example and for which I added the management of BLE LE Secure Connections (inspired by https:...
Hi all,
I observed an issue after upgrading to 1.8.0 and to Zephyr 2.7.0-ncs1 respectively. When having Zigbee (and NET core) enabled, all images are built as before. The...
Hello there,
I've set up 1.RaspberryPi with an otbr docker container.
Thanks to Sigurd I have set up 2.nRF21540DK running CoProcessor firmware built with nRF Connect SDK...
Hi,
I want to know more about composition data size. As I have read in Mesh Profile v1.0.1, composition data page 0 is mandatory, while the other pages are optional. The...
I have custom board defined in DTS file. There will be multiple variants of boards, therefore I need to check which board is selected. How to check which board is selected...
Hi,
We are using nrf52840 for custom design and we have replaced the mx25r6435f qspi flash with Cypress S25hS512 qspi flash. We configured the flash as below in the dts...
Hello,
We have nRF52832 devices in the field, and one of the leading causes of warranty returns is that flash of nRF52 is completely erased. nrfjprog --readcode and --readuicr...
Hello,
We have a problem that affects a few devices (< 0.1 %) in mass production. The devices are flashed, boot up and pass tests and get shipped to customers. Some customers...
