I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi, I'm trying to found a way to flash production config for a project based on zigbee NCS example with OTA. Is nrfutil still a valuable tool for creating a production config...
Hi.
I'm trying to emulate my project, which is intended to run in either nRF9160 or nRF5340 boards (both using Arm Cortex-M33 processor), using QEMU, but as far as I know...
Hello,
I am using nRF52840 microcontroller to communicate with an external integrated circuit, through I2C peripheral . The project is using the latest Nordic SDK: more...
Hello,
I am running 1\nRF5_SDK_17.1.0_ddde560\examples\dfu\secure_bootloader\pca10040_s132_ble\ses example of SDK 17.1.0. Now, I want to update the firmware when it is pressed...
Dear Ladies and Gentlemen,
I read for detecting angle of arrival the following page:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth...
Hi,
I want to develop simple app that receives data via BLE and send it through UART so I could gather them to file or draw a real-time chart in SerialPlot.
As far as...
Running the secure DFU example in SDK 17.1.0 results in hardfault in IAR EWARM 9.10.2. The board used is PCA10040.
Using EWARM 8.50.4 seems to work without problems.
Steps...
I have a number of custom projects and boards that were created using SES.
How do I get nRF Connect to see my projects and boars. I have a separate directly structure where...
if i am controlling two spi devices with one instance, can I just define a new SS in the same SPIconfiguration or do i have to close the connection and select a new one? ...
As soon as I plug in my nRF52840, the whole board gets extremely hot. When I try to upload a program, the error message "No J-link device connected" pops up.
With another...
Hi!
I use XMONITOR to get the current cellid but it seems strange.
%XMONITOR: 5,"","","24008","2725",7,20,"01ADF70B",215,6400,50,35,"","11100000","11100000","01001001...
I'm working on nRF9160-dk.
I built a sample application "serial lte modem" in NCS 1.6.1.
i can use AT command on the UART0, but i find the printk in source code is not...
I have successfully compiled my project using `west build` and now I am trying to load it onto my nrf5340 board I recently purchased. Here's what I'm doing:
- From the same...
Hi,
I would like to test some environments. Therefore - I would like to use an example from SDK 17.0.2, which allows me to connect to a PC via NFC, as a peripheral, receive...
