Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Wireless Communication Synchronization System Based on the Alignment Principle
A year ago, I proposed the wireless communication synchronization system described below....
I am going through Lesson 9 of the nRF Connect SDK Intermediate course to understand how DFU and FOTA work in the SDK. I am using toolchain and SDK v3.1.0, and nRF Connect...
Testing a new nRF9151 device using a project derived from the Nordic "HTTPS client" sample project. We are experiencing a "Modem has crashed" event intermittently when running...
Hi，
Background Information:
Our product, BLE near-infrared device , is undergoing CRA (Cyber Resilience Act) compliance assessment—specifically for the EU RED Cybersecurity...
This seems like a silly issue, but I cannot get the UART output from the nRF9151 DK. Attached is a project that outputs via both LOG and printk() to a Segger RTT viewer without...
Hello,
I am working on a simple Bluetooth Mesh application for light control.
I started from the provided samples: - github.com/.../light - github.com/.../light_switch...
I am trying to program an external board using the development kid following the instructions HERE .
I am using the debug out P20.
I have tried supplying the board frm...
Hi,
I am working on ncs 2.9.1 @ nRF54L15.
I followed this academy course to add a single channel saadc in simple mode:
ADC read works properly, but the current read...
i built a small breakout board for npm1300 (QEAAD0 2516AA) to experiment with it. the twi pins are wired to the i2c ports of a raspberry pi 4 to control it, and i have attached...
I do measure different values for source and ampere mode. On the nRF52 DK. Source Mode: disconnect SB9, Power Switch is off. Vout from PPK2 connected to nRF current measurement...
Hello,
We are using NRF5340 in our product and running automated hardware testing. As part of this process, we need to program the chip twice: once with a dedicated testing...
Hello,
I am using nrf52833-dk for making a ZigBee coordinator. I am using "network coordinator" sample code.
The project is making a ZigBee connection between "nrf52833...
My error message is that it works on a computer, but it doesn't work on the company computer. I'm not sure if it's the encryption software on the company computer, but I don...
I have a 5 year old design using a nrf52832 on a MDBT42Q module. The BLE option was placed on the PCB in 2020 and has been unoccupied since going into production. My customer...
Hello,
I am trying to build the sample/sensor/lps22hh project on nRF52840 DK and STEVAL-MKI220V1, but receive errors in build.
I have added an overlay file as in boards...
