Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hello
I'm trying to get spi to work on nrf52. First tried to use it with adxl372 driver but got nothing on device_binding returns null. Next I tried to create own driver...
Hi, I am now studying on the basis of advertising tutorial example.
When I connect to the device, I want to turn on the led4 in the main loop(To just study), but I don't...
We need a simple program that can be used as a terminal program on Windows (with nRF52840 dongle attached) to a remote device running the BLE UART service.
Essentially,...
I would like some guidance on how to start a project using the nRf52840 - i.e., what sample programs would I start with? The project is a remote control lighting application...
I used the example pin_change_int from peripheral examples and commented the OUT pins. In addition I added the sleep commands to the main while loop. This is the code:
...
Hello everyone,
I'm currently working on a project that requires a nrf52832 chip to relay raw beacon data over UART to an esp-12F module. I am having a difficult time figuring...
Hi.
I have NRF52 DK.
I have successfully flashed TWI sensor example on to the board.
However, when I move forward with other projects in SDK like ble_app_uart and ble_app_blinky...
Hi I wanted to ask if there is a driver/library for the mcp25625 chip? Also for the communication do I use " SPIM — Serial peripheral interface master with EasyDMA " or "...
I'am achieving lowest power consumption in connected mode. I can't identify source of short spikes every 40Hz when mcu is in low power mode. I'am sure that it's not application...
under code is my sdk main code and i want to change code to Sensor --I2C-- nRF52 --UART-- app but where i have to start and change ?
/* Copyright (c) 2010 - 2017, Nordic...
I've been doing some testing with Mesh DFU and I've noticed some unexpected behavior around handling missing data segments.
As I understand the Mesh DFU protocol, if a data...
I have issue about calibartion using saadc.
I use 52832, S332, SDK 15.3.0
when calibration is excuting, ANT+ and BLE is also doing.
I use low power mode in saadc.
...
Hi
I want to know if there is any source code of thingy91.
Because I want to follow thingy91 for making a product with the use of the same antenna, and I want to know...
Hi,
Recently, I was trying to move my project from STM to Nordic IC.
I just wonder how to implement the below codes into the nRF52832 or how to program it in Nordic environment...
Hi,
I want to set sending power(+4dBm) of NRF52810/NRF52832 with SDK 15.0.
Now,i find i should use the order of sd_ble_gap_tx_power_set(uint8_t role, uint16_t handle,...