I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
I did current measurement for NRF52840. For mesh light switch demo example measurement was 10 mA, and for Thread CoAP Examples current measurement was 0,6 mA. I don't understand...
Hi all,
I am developing an application for a product where power consumption is critical. The application is bundled with the Secure DFU bootloader. I noticed that the bootloader...
Hello,
I think the question may be more related on how Wireshark works but I plan to do the following:
* use the v2 sniffer firmware and the Nordic Wireshark plugin
...
When I migrated, the reference routine output PWM, but kept reporting errors. I have also changed the relevant definition, but I still can't. Has anyone met it? Thank you...
Hello,
We're evaluating the Laird BL654 using your nRF52840 (to be precise, we're using two DVK-BL654-1.0 development kits).We tried to use the 'blinky' examples (ble_app_blinky_c...
Hi everyone,
I am developing a remote controller using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
Hello, everyone~
I plan to use the Low Energy Secure Connection funtion with nRF51822. But when I build the lesc example in SDK 12.3.0 (ble_multirole_lesc), there's a error...
Using the sdk15 and softdevice 132 v6, I'm setting up an app to read and write to an SD card that uses SPI1 (SPI0 is used by a display). Everything is working great, except...
Hi,
What's is the max length for the payload data in "mqttsn_packet_sender_publish" method?
EDIT:
Redefining my question above: What's is the max length for the payload...
Hi Sir,
According the table 19.4.2 of 52832 datasheet (v1.4), there is a start up time (0.36 ms) for HXFO.
How do I measure the start up time of my 32M crystal?
If...
Hello,
While an attempt to develop solid security mode bulded around Root of Trust starting from RTL and Device root key we found that unfortunately, it is mentioned in...
I would like to detect if a reset happened due to a brownout or an actual power off.
I tired so far using the GPREGRET and RESETREAS registers. They are useful to detect...
I have an app that works perfectly when run from the debugger, but not when started by HW reset. We use the serial port to communicate to a control processor (STM32) The Nordic...
Hi,
I was trying to test a slot circle antenna with nRF52832 which is well matched to 2.4G~2.48GHz, but it is circular polarized antenna with high directivity.
However...
Hi All!
I use nrf51822 with sd s110 to send data to android phone with sd_ble_gatts_hvx. If sd_ble_gatts_hvx returns NRF_SUCCESS then that packet get to TX buffer. I didn...
