Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I have seen this assert since SDK 2.4.2 but less frequent. Now I had updated the code use the SDK 2.9.2, this assert made impossible to release it to production.
The point...
Hi Nordic team,
I am tring to make a BLE mesh net, I use two promicro(nrf52840), one for mesh_provisioner_example, one for mesh_on_off_app_example.
But mesh_provisioner_example...
Hello everybody.
I'm experiencing a problem with two nRF54L15-DK boards, one flashed with sensor clent sample (Client) and the other with sensor server sample (Sensor_srv...
NCS3.1.1, NRF52840, Windows, VScode
I have been trying to add MCUboot to my product, without success.
I believe there are known issues related to debugging when MCUboot...
I'm using the RTT log feature in NCS, and here is my prj.conf:I have two questions:
After using LOG_INF to output logs, I feel the logs are not output immediately. Since...
Hi,
I’m working with an nRF52840 that supports Bluetooth Low Energy updates via MCUboot.
We want to enable APPROTECT on our production units to prevent competitors from...
My understanding is that when the module's measured RSRP is lower than that defined in the broadcasted SIB, ECL will be escalated to higher level during RACH process.
Besides...
Hi,
I found out that my Matter device does not commission to Alexa because as part of adding the device Alexa will try to read FeatureMap attributes from all clusters and...
Hello! I'm working on some project using Fanstel BM832 module. I'm using the configuration based on board nrf52dk_nrf52832, with some minor modifications (led's and button...
Hi:
I'm doing the exercise L3-E1.
I used nRF Connect SDK Toolchain v2.7.0 because it didn't work with v2.8.0
How do I make NRF Terminal appear?
Thanks and Best...
I have a quick question about configure i2c.
I have the following schematic:
And the following configuration for the nrf54l15 :
And the following in prj.conf:...
Once the nRF52840DK is running the Zigbee light bulb demo I cannot flash new code to it unless I disconnect the board and reconnect it first.
I am using nRFConnect for Visual...
Are there user programable once registers on nrf5340 that I could use to store board hardware version? I looked at UICR, but I think they get erased when the whole chip is...
I added FOTA over Bluetooth to my NRF52840 application. Everything works, I can update the application over bluetooth and it runs properly, but after updating if I unplug...
