I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi,
I have three nRF52840 DKs
I am trying to connect two of them as peripheral devices( that implement the ble_app_uart example)
to the third nRF52840 central device...
Hi guys new to the Nordic family of devices, but can the thingy91 provisioned on a third party cloud platform other than the nrfCloud? Also can I use a different sim-card...
While migrating to the latest nRF5 SDK (17.0.2) and nRF for Mesh SDK (5.0.0) , I've noticed that they ship with Softdevice 7.2.0 .
The latest s132 Softevice available for...
Hi,
I understand that scan request allows the broadcaster to send additional advertising data. Does it send the additional data via data channels? Is it related to secondary...
SEGGER ver 5.50d
nRF52840
I'm trying to find a way how to use the STL library with GCC compiler. I know that SEGGER is not fully supported STL library (a basic stl library...
Hi,
We are developing a solution using nRF52 and nPM1100 using nRF5 SDK 17.x? I was wondering if there is a software library already written for the nPM1100?
Thank you...
Is it possible to change the smartbasic firmware? and if I want to return to that firmware how can I doit?, and last one, if I use de nordic SDK with the DVK BL654, does it...
Optimization level is set to "Debug". Tried to change it to one of the Levels, however then firmware does not run at all. Debugging Level is set to Level 3.
Can it be other...
I want to develop the nRF series at segger embedded studio for the first time. But I tried the following homepage to install manually. www.nordicsemi.com/.../Segger-Embedded...
NCS(nRF Connect SDK) is a good environment to develop nRF52,but it seems not stable until now.
I want to use NCS(nRF Connect SDK) to develop my project ,and met some unknown...
Hi Supporter,
I use apptimer in proprietary_rf gzll, I used as below ,but it doesn't work.
1) app_timer_init(); ,here I ennable the RTC1 in the sdk_config.h
2)app_timer_create...
Hello NRF ,
I have been using NRF9160 DK GEN-1 board for NB-IOT and GNSS tracking and able to configure my network SIM as well as the NRF cloud .
I have used SDK 1.4.2...
Hello There,
Basically I just want to get Sensor data like (Temp Sensor) who already connect to Arduino and I get it , So I just want that data to nRF9160 over UART in...
Refer to nRF52840 Technical Manual USB 2.0 (full speed (12 Mbps) controller) The USB2.0 rate can be up to 480Mbps. We have a product whose USB transmission rate must not be...
