here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hello.
C21, L5 and C22 are part of antenna matching. And, L6,L7,C23, C17,C19,L4,C20 they suppress the harmonics and spurious responses and match the chip to 50 ohm. R19...
Hello,
I am trying to setup the DTM to evaluate our product. I am using shielded boxes and following the setup from application note 34:
I am unfamiliar with this...
Hi all,
I added ble central multilink example with ble_app_uart_c code, i am able to compile code successfully, but not able to run this code on board due to this error...
Hi!
I am developing a project where an NRF52840 DK is receiving data from the environment using BLE. I can observe the received data using NRF_LOG_xxx() command in my...
I'm trying to use the PA/LNA control feature in S112. However I only want this to be enabled when under specific conditions/configurations at runtime. So I need a way for...
There are 6 channels per the SDK (nRF5_SDK_15.3.0_59ac345) and the product spec for nRF52840 but I cannot seem to get channels 4&5 to do a compare or capture. Using Keil's...
Anybody got any hints at how to get Zephyr to work on the nrf52840 PCA10059 dongle?
After many struggles, I was finally able to compile Zephyr's sample/bluetooth/hci_usb...
Hi there,
I am trying to get I2C communication up and running with the nRF52832 (specifically configuring the nRF52832 as a master to communicate with 3 slave devices),...
Hello everyone,
I am developing a temperature and gas sensor for indoor environment monitoring. Due to the limitation of the bluetooth transmission range, I hope to add...
Hello, I am developping on a nrf52840-DK board and try to debug using a Black Magic probe. Software is based on softdevice, GCC build chain and Visual Studio Code with Cortex...
I've been wrestling with this DK for some time now, but today I tried to get the LTE Link Monitor app to run and see what outputs I could get. I ran everything the same as...
Hi,
I am having issues, getting the uart backend logging working on a nrf52840 dongle. I'm testing the logging on the standard blinky example that came with the sdk (15...
Hi,
Upgrading from nrfConnect for Desktop from v 2.6 to v 2.7 and higher and its associated apps seems to hang on Linux (ubuntu 16.04). 'strace' suggests that the problem...
I have a design which mainly needs to be a peripheral, however I was told that I need to use the multi-pheripheral example as I may need the device to switch to a central...
