I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
I've used the nrf_inbuilt_key_write to store certificates/keys in the past, but I am still unable to do it using the "AT%CMNG" modem command.
I can list and delete items...
I attended Nordic Tech Tour - San Jose (Cupertino) on June 11. I did not receive a link for the presentations, as was communicated. Please advise how I can get the Tech Tour...
The BWG832F DK Bluetooth Gateway comes with a board that says that it can be used to program the Bluetooth module. The software recommended for this is the Nordic nRFgo Studio...
Hi everybody,
I'm using nRF52832 on a custom board mounting a BME680 sensor.
I'm running a third party library for the usage of the sensor (namely BSEC Library), and it...
Hello everyone, After having designed a pcb by taking the scheme proposed by the datasheet, I uploaded by the Black Magic Probe, the example code of the SDK "receiver Radio...
Hello,
I'm using the watchdog and i'm feeding it in my main loop :
I tried with
#define NRFX_WDT_CONFIG_BEHAVIOUR 1
and
#define NRFX_WDT_CONFIG_BEHAVIOUR 0 ...
Hello
I am using nrf52840 and am trying to determine the parameters of a voltage divider using the SAADC. Vin is the VDD voltage of the chip, R1 is 4640 ohms and R2 is 38600...
Hello Community,
I successfully build and run mqtt_simple it works fine.
I edit the code
//////////code///////////
void main(void) { u64_t start_time_mqtt; while(1...
Hello,
I am having an issue with the GPS on the nRF9160. I have been developing a custom program that will switch between NB-IoT and GPS when an interrupt pin is triggered...
Hi.
I am curious to know if it is possible to use the ANT-only Softdevice with the Zephyr RTOS. The goal is to create a BT BR/EDR + BLE 5.0 + ANT+ device all on the same...
Hi,
What is the maximum frequency that i can capture on GPIO port of nRF52840 ?
I'm planning to capture a frequency of 32MHz from a sensor on GPIO pin , can I do this...
Hi,every one!
As far as i konw, the original connection interval that ios sets is about 50ms, that is a little too fast for me, so i want to change the connection interval...
Hello,
Ive got an question of my Central BLE nRF54280 Dongle. I want to read the advertising packets of Sensors with the Name "RH". Shouldnt be a big problem. But i got...
Our device is based on nRF52840 with SDK 15.0.0
The device communicates over BLE with PC application (aka client) via "uart" service.
PC (client) messages are signed using...
