Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I have followed https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a-beginners-tutorial
i WANT TO ADVERTISE the battery...
Hi,
Segger SystemView 3.30 (downloaded from https://www.segger.com/downloads/systemview/ ) does not work with NCS 1.5.1. Upstream Zephyr has updated https://github.com/zephyrproject...
Hi Nordic,
I just had Thingy:91 few days ago. I ran this KIT with thingy91_nbiot_2021-03-04_8e8c6089.hex and asset_tracker example in ncs/nrf/applications . I found that...
I would like to send and receive data to/from nrf52832 pins over BLE using android phone. I would like to capture and display output of Force Sensing resistor and control...
To the kind attention of Nordic support team,
We have got an nRF52833 gzll host that has to interact with multiple gzll devices. We empirically saw that (in our case and...
Hello
I'm using the CLI example as ZC and a custom endnode based on the freeRTOS multisensor example (from nRF5 SDK for Thread and Zigbee v4.1.0). Im trying to send a counter...
Hi, I have a problem with setting up SHELL over RTT. I have managed to get some logs from the device. Prompt `rtt:~$ ` is also shown. but whenever I try to send something...
Hi,
we just uploaded MFW 1.3.0 to our nRF9160 DKs that had engineering revision of nRF9160. They seem to be now bricked and it is not possible to downgrade to MFW 1.2 via...
My task is to create a webserver on the nRF9160DK. For this i'm using the civetweb module provided by zephyr and the ethernet-shield from PHYTEC. I got an issue i want to...
Hi everybody,
I have developed a BLE sensor based on nRF52840 (S140 6.1.1 and SDK 15.3.0) that is normally performing connectable scannable undirected advertising. Since...
Hello,
I need to use the ADC with 600mV internal voltage, ADC Gain stage = 1.
The input signal on VINP vary from 750mV to 1750mV, and input signal on VINN is fixed at...
Dear friends,
I followed the tutorial( Using serial interface for provisioning and configuration ) control a mesh node.
a) The PyACI as a host via uart connet to 52840...
Hi, teams.
I checked the operation of nrf mesh network. (mesh sensor example, and light switch example)
It works well. Thank you!
By the way, I have a question....
Hi everyone,
I am having a problem with dfu example. I would like to test my board with the buttonless dfu image, namely
sd_s132_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
Hi,
I saw a similar post ( Case ID: 249969 ) and this just happen to me.
I have not used my nRF52840 DK for a few weeks. It has been in its original plastic bag the whole...
