I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi engineers, I got a question regarding nRF52840 (PCA10056), i want to run DTM using PCA10056 board with MT8852B tester. Unfortunately, i keep failing to get the EUT address...
Dear all,
Our application is made of
Chip nRF518122 + SDK 11.0.0 + DFU Bootloader + BLE application (gcc complied) loaded with nRF Toolbox over the air
we are putting...
Hello,
the nRF9160 product specification 1.0 states in 5.1.4.2:
"Note: The LTE modem requires using LFXO as the LFCLK source."
I checked the clock register and noticed...
Hi,
I have developed an SWD working code which read-write the Flash Memory and RAM which is working very good.
Now I have a problem in I need to write start address...
Due to time pressure, I'm starting this thread based on an existing ticket: https://devzone.nordicsemi.com/f/nordic-q-a/51423/firmware-on-custom-board-application-bootloader...
Hi team,
We have a customer who has some questions about GPS.
The questions are:
Where do we save the Ephemeris data when GPS code start? RAM or flash?
When use...
Hi,
Can an nRF5x device be configured as a BLE relay with Bluetooth Mesh?
I believe with the Central-Peripheral-Relay example, the Relay needs to establish connection...
Hi. I am trying to create a dfu zip file that contains the softdevice, bootloader, and application. I am DFU upgrading an NRF52 device from SDK v13 to SDK v14 via Nordic's...
Hello,
we are using the nRF52840-DK.
File: secure_bootloader_ble_s140_pca10056.emProject
File: ble_app_buttonless_dfu_pca10056_s140.emProject
In short, we are...
Hi,
I have a well working cli environment under linux where i can compile, program and debug a nFR52 demo board.
I have installed RSSI Viewer (1.05) and Bluetooth Low...
We want to deactivate Mesh DFU packets relaying from the App side to avoid messing with the bootloader firmware. Is there any flag we may use for that?
Hi,
I'm trying to use a Bulk IN endpoint (EPIN3) and am running into an issue.
I call the nrf_drv_usbd_ep_is_busy() function to test whether it is safe to proceed with...
Hello
I am using buttons less DFU,
S132_nrf52_6.1.1 softtdevice
using Android + nrf connecct, I can update the device with DFU
using IPhone 6, I can not update...
I am able to provision using BlueZ's meshctl tool on Raspberry Pi3. However, after restarting meshctl, I am not able to control my device. I tried the "connect" command after...
