Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Dear Sir,
I have purchased nRF5340 DK (Will call it device hereafter) and am trying to bring it up.
I have connected the device to Linux but the device was not detectable...
I’m testing the nRF9151 DK in India and trying to use the nRF Connect app (Quick Start guide) to connect the device to the network.
Board: nRF9151 DK
SIM: Onomondo...
I have a nRF52DK board that I loaded the peripheral_uart program in a while ago. I tried to get the board running again but when it calls err = settings_load() it just keeps...
I'm currently trying to integrate Memfault to my project that is using nRF9151 DK. Memfault was working fine until I turned on these configs:
# Collect LTE Metrics CONFIG_MEMFAULT_NCS_LTE_METRICS...
The application here is reading a Manchester stream on a GPIO. which comes from a MAX41473 radio IC.
Decoding is working fine using GPIOTE, timers & PPI to time & decode...
Hi,
I have two nrf9161 dev kits. I have flashed the firmware 2.0.1. Then I flashed the hello_dect example.
Now I always get an error and the program does not start. *...
Hi,
I am able to do some stuff partially using the command
$ west build -b nrf52840dongle_nrf52840 -- -DDTC_OVERLAY_FILE=usb.overlay -DOVERLAY_CONFIG=prj_cdc.conf
With...
Hi guys, I am using the SDK v2.9.0 and the toolchains b620d30767. To add the build configuration for the sample peripheral_uart, the console print some error log.The log as...
Hi all,
Im' tryint to acheive a aws fota firmware update on my custom nRF9151 board but I'm stuck. Here is my setup and what working
- Custom board build with a nRF9151...
Hi,
I would like to perform channel sounding on nRF54L15 DK,
I tried to compile sample "channel_sounding_ras_initiator" in nRF Connect SDK v2.9.2, but error message says...
I'm getting an error when I try to push my branch.
remote: Permission to NordicDeveloperAcademy/bt-fund.git denied to batir.
fatal: unable to access ' github.com/.../...
Hi, I am looking to setup my nvim installation with a debug config to match ozone, but need some help getting started. When I debug using VSCODE I seem to miss crash, reboot...
For an application developed using the latest nRF Connect SDK v3.1.0, how would you recommend configuring Bluetooth performance to maximize connection range for nRF52840DK...
Hi,
I'm trying to pass to v3.0.0 from 2.6.0. I've install the new toolchain from nrf connect desktop app, everything works. I go to vscode add new build configuration, selected...
Hi, I'm programming via SWD nrf51822 chip using nrfjprog with nrf54L15-DK as programmer, with this script (Windows 10 or 11 OS): ECHO OFF nrfjprog --recover -f NRF51 > nul...
