Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
I am using the Zephyr SPI driver to control a WS2812 LED strip through the SPI interface. Since only the MOSI line is required for communication, I want to configure the SPI...
Hello, I have an application developed with the nRF9161 DK board, which essentially consists of a GPS tracker that acquires a position every x time and sends that same position...
I make a ble hid usb dongle with ncs2.0, ble keyboard send keycode to hid dongle, hid dongle send the keycode to computer.
When keyboard send keycode slow, it's work fine...
Using 54L15 DK for testing. Zephyr toolchain & SDK both v3.02. I have been through the DevAcadamy exercise which uses Blinky for its example, now I want to integrate into...
Hello,
I need help regarding flash memory read on nRF52840 device, SDk16, SD=340.
I have using the fds libarary for memory read/write in my code for many years now. However...
Hi,
I'm trying to scan for coded phy devices with the nrf-sniffer application.
Followed the guide and installed nrf-sniffer with the nrf-util.
In Wireshark it works...
We are using firmware 1.3.6 on the nRF9160. During testing, I ran into the reset loop restriction. To quickly get out of it, I issued a AT%XFACTORYRESET=0 command. (We are...
Hello Nordic Team,
I am using nRF5340 DK as a debugger/programmer to develop firmware for the Fanstel EV-WT02C40C module. My goal is to use Wi-Fi (nRF7002) Wi-Fi scan, Wi...
Hello! I am trying to upload the basic applications to the Thingy:91 X from the downloads tab, here: https://www.nordicsemi.com/Products/Development-hardware/Nordic-Thingy...
Hi,
I just noticed that there's another issue with my project after upgrading from SDK 2.3.0 to 3.1.1.
I am using the 802.15.4 radio for low level packet communications...
Hi,
for a project based on the nRF54L15, we are evaluating the new single-slot DFU mechanism.
Using NCS v3.2.1, I am testing the sample available at: https://github.com...
Based on the DevAcademy here is my following setup using a custom NRF54L15 chip with the NRF54L15-DK devicetree with following overlay:
prj.conf:
CONFIG_GPIO =y
...
I'm trying to configure the nRF cloud log backend to aid with debugging of devices during field tests without the need for bulky UART harnesses to capture logs from the serial...
Hi everyone,
We’re trying to use UART1 on the nRF9151 DK in non-secure mode , mapped to the Arduino R1 connector. However, it seems to be reserved by TF-M , and we cannot...
