Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello everyone, I have a firmware running on nRF9160 which was developed with nrf sdk v2.2.0, now I want to update it to use nrf sdk v3.1.1. I cannot build the firmware when...
Cause of the issue Earlier, when I were producing products ( around 600 units with 2025.9 ), about 30% of the chips had difficulty connecting. Later, it was found that the...
Hi,
I am implementing a custom bootloader on an nRF52840. The firmware update is downloaded while the main application is running. The flow is as follows:
The application...
Hello I'm working on a nRF9151 DK using nRF Connect plugin for VC.
I was able to program and run my without any problem... but then suddenly the flash process stopped to...
Hello.
I use the bare metal SDK and I would like to generate a GRTC interrupt every 250ms to wakeup my system.
Which resources does the zephyr is already using (GRTC_x_IRQn...
Hi,
I’m using an nRF52810 with nRF Connect SDK v2.5.1. I want to read the internal temperature sensor. I started from the LBS sample and added NSMS to report the temperature...
I'm working on the firmware for a custom board built around the nRF9151 SiP. The firmware is built against the nrf9151dk/nrf9151/ns board target included in zephyr, with an...
HI
I am using nRF54L15 PDK with NCS 3.0.0. In my code, I am using NVS to store data on the MX25R64 flash on the PDK. The initialization code is as follows:
struct flash_pages_info...
Hello, I am currently working on a PDM microphone project using nRF52840 and Zephyr RTOS. I've been testing the official Zephyr sample (located at dmicncs/v2.9.0/zephyr/samples...
I have three questions regarding the electrical parameters of the NRF9151 chip:
For a GPIO configured as output: What is the maximum source current per pin when driving...
Hi,Team,
I am developing the nrf54l15-dk, and the version of my NCS is v3.0.2. Because our terminal device 1 does not support using ble-FOTA, I used another terminal device...
Hi,
We have a custom nRF9160 board with chip antennas for LTE and GNSS. They are Ignion antennas with matching circuits customised to our board dimensions. We also use...
Hello, We are developing an application with nRF52810 based on nRF Connect SDK V2.4.1. The application is utilizing the BLE connection, particularly the NUS Service (emulation...
