Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I'm using the NRF9160DK board. I'd like to connect the UART port from 9160 to the 52840. The 9160 is running SLM firmware. The 52840 is running my code.
My question...
Some helpful pictures referenced in documentation (asset_tracker_v2_description.rst) are missing:
missing at least: figure:: /images/asset_tracker_v2_module_hierarchy.s...
I am using below environment for my project
NRF connect for desktop version 3.7.0 and Programmer v1.4.11 in windows 10, NRF52840 and Jlink debugger
I have tried multiple...
Hi!
I have a question regarding the scan timeout. The situation is the following:
On a nRF52840, I repeatedly perform scans every 120s (which is controlled by a CC Interrupt...
hi
I am using nr5340 and it adrvertise as nordic_lbs.. but i want to advertise through beacon sample. it still shows nordic_lbs in my mobile nrfconnect software. but it...
Hi,
I am also facing same issue i am able to read the version register correctly and able to perform self test successfully
I am using 17.1.0 n RF5 SDK
I am using SPI...
Hi, my 1-button system off/on example works perfectly fine on nRF52 DK. However, when I move the exact same code to nRF52805, there are some errors.
I choose pin 21 as the...
I've been trying to send fast data with NRF24L01 for a long time. In order for the project to meet its requests, 32bytes of data must be on the Receiver side at a maximum...
At 1M rate, test the reception sensitivity of Bluetooth chip, the number of packets lost at -90dBm exceeded 30.8% as specified by Bluetooth Alliance, and this situation occurred...
hi all, i download the project from github master branch, i also added " pip3 install - r zephyr / scripts / requirements . txt " but still, i got the same issue. i had read...
Hi, I am not sure how to measure the signal strength of the communication within the mesh network (ie. communication between provisioned nodes), in order to verify a change...
Hello all,
Currently I´m developing a code to be load to the SDK to act as a master in a BLE communication. The peripheral is a BLE thermoter that, in order to preform bonding...
I'm attempting to revert an nRF52840 dongle to the production bootloader. This dongle has a SWD connector soldered on for use with J-Link, and I have no difficulties flashing...
Hello everyone,
We're developing an application that manages the LTE Link reconnections automatically, without interfering the GPS performance. For such purpose, when there...
