Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
The goal is that we can update the firmware version with the smartphone or tablet without having
need to go through the development tools
(cable, IDE, ...)
if so, how can...
Hi,
In our firmware we're writing the entire contents of our UPDATE.BIN file successfully with flash_img_buffered_write's, but after boot_request_upgrade and a sys_reboot...
When my Nordic device is running my custom BLE application I notice that the device address is 0xC4318DBD687C. When device is running the bootloader service the device address...
Hi Nordic,
As far as I can see, there is BLE_NUS_CONFIG_LOG_ENABLED defined for ble_nus in sdk_config.h. However, I cannot find the similar BLE_NUS_C_CONFIG_LOG_ENABLED...
Hi, can we use a manufacturer name of our own for the usb in nrf52840?
We know that we can still use the Nordic Semiconductor's usb vendor in a commercial product.
Best...
Hi, Can I use nRF24LE1-F16Q24-DK without nRFgo Starter Kit? If yes please suggest me programmer to program nRF24LE1 by Keil IDE. by referring documentation I found its support...
Hi
SDK v15.2.0 SD 6.1.1
I have managed to send out "Connectable, Non-Scannable" extended adverts with some AD packets as payload. On a frontline sniffer as per the file...
I am developing a HID keyboard based on an nRF51822.
The firmware source available here:
https://github.com/martonmiklos/ble_keyboard_fw
(It is based on the ble_sdk_app_hids_mouse...
Hello,
i'am trying to control the pwm Idle State Level.
between my Sequence's (1sek) the PIN stays High But i need it low.
I try to set the GPIO Out Register, but...
Hello,
I am working on a simple Bluetooth mesh example setup with the following configurations:
nRF52832 DK: light switch server, subscribed to group 0xC000
nRF52840...
We have a mobile app on iPhone and Android, the NRF52 advertises every 3 seconds. The app can discover the NRF52 quickly but it takes a long time to connect. The iPhone is...
Hi,
I am developing a system that will read from a sensor that uses I2C and then transmit this to a "master" using ANT+ or BTLE (this isn't decided yet)
For the prototyping...
Hello,
Where can I find the pre-built binaries for the below Provisioning options :
1.OOB (Public Key) and Authentication - Input
2.OOB (Public Key) and Authentication...
Hello.
I have an nRF51822 chip and I'm trying to figure out how the whole nRF5 sdk works.
I am using the Segger Embedded Studio.
I downloaded the last nRF5 SDK v15.3...
