Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
This question is based on the NCS tag v1.8.0.
I am using nRF9160DK SLM application to evaluate the MQTT AT command function.
I got OK if I send a plain text to...
Hi Sir/Miss,
I import cts (current time service) as previous topic which is as link .
I have a compatibility issue in different phone.
The tested conditions are as...
Hi,
I'm thinking of doing a send / receive test of nRF52832. The Bluetooth test set uses MT8852B (anritsu).
At that time, it is necessary to send a signal by HCI or 2...
In the nrfConnect SDK 1.4 there is a sample for chainable RGB LEDs ../ ncs/zephyr/samples/drivers/led_ws2812
I want to use this with nrf9160 so I created nrf9160dk_nrf9160ns...
Hello!
I am able to use the Direct Test Mode application on the nRF52833 development board using the pca10100 DTM firmware found in the 17.0.2 SDK over USB. However, when...
Hello, When I use the recommended X1 and X2 crystals from Epson (Q22FA12800025 and FC-135 32.768KHZ ±20PPM,9.0PF) the device works properly, crystals from ECS did work too...
Hi,
I am doing a design with this component MP06003, but I don`t find this in the distributes in Argentina.
I am looking for this components with others distributes...
Hello Community! I've recently switched from Master Control Panel to NRF Connect. I want to use my NRF51 Dongle (PCA10031) with NRF Connect. Therfore I deleted the existing...
According to eval kit reference BOM list a TDK MLZ1608M100WDT25 10uH coil is the only one on list. Is there any other suggested coil models tested by Nordic? Just wondering...
We are designing a custom antenna for the nrf52833-QIAA. Could you supply the output impedance of the ANT1 antenna pin so that we can run an HFSS simulation on our layout...
Dear Members,
I run 3 devices,
GPS on libuarte1
LCD on SPI2
Sdcard on SPI 1,
I'm using ANT and softdevice 340,
When I run LCD and SDcard outside the main loop...
Hi,
I am having problems with the ble_advertising_int() function. It returns a return code of 12 (NRF_ERROR_DATA_SIZE) which is returned by ble_advertising_init() -> ble_advdata_encode...
Hi I ran in some problems with my BLE fragmentation. I want to send data (files) up to 6kBytes over BLE (Bluetooth 5 on nrf52840 to another nrf52840). My project is based...
