Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hi,
I had a problem while testing using the app_app_uart.
I added custom service and set tx buffer size to 70.
I tested using nRF Connect.
And, i got error message...
I received a bunch of Thingy:91/PCA20035 version 1.4.0 which upgraded the SWF connector for GPS antenna to a uFL/IPX connector which is great. I also have a few PCA20035 version...
Hello,
I'm using SDK for Thread v.4.1.0 along with nRF52840 microcontroller. Starting from MQTT-SN examples I developed a Thread network with multiple nodes, publishing...
The nRF51822 QFAC-R has a drive level of 1uW max for a 32.768KHz crystal. We would like to use an Epson crystal with 9pF load however its max drive level is 0.5uW. What are...
Hi,
I am have programmed my Thingy 91 device with lte_ble_gateway program to collect data from 5 Bluetooth devices and send them to the cloud. This program runs fine,...
Hello Within my Thread network, I have a lot of Thread devices (with a lot of routers). Every now and then I need to multicast data to the whole network (I use the address...
Hello,
I am trying to read BMI160 outputs using SPI protocol but I am struggling to get a successful build from my code.
The build fails at the first line of my code...
Hi,
I am trying to write a file in flash(nrf52840) at a particular address & after that i want to instruct DFU module to start FW update from that address?
Is there any...
What are the situations where a SoftDevice calls reset handler?
I have a somewhat heavy data collection (lots of event handling) and those things are logged via RTT backend...
Hello,
I developed an application on a BMD-300-EVAL. This is a evaluation platform with a BMD-300 module (nrf52832 chip + antenna + crystal +...) on it. The application...
Hello,
I have followed all the Getting Started documents to setup the development for my new nRF9160 DK.
Among them, I installed SAGGER Embedded Studio version 4.52
...
I have as starting point the HRS FreeRTOS app. Now I want to add a millisecond counter. But from what I read I'm a little bit confused. Can someone tell me what's the best...
Hello, I am working on a custom NRF9160 and I am on SDK 1.3.0. I am working on the asset_tracker project and I want to put my own accelerometer there. To do this, I changed...
Hello,
I have been using Nordic mqttsn examples (publisher/subscriber) along with an OperThread Border Router. So far I haven't changed the parameters of the Thread Network...
Hi,
I am trying to adapt the read register function that use the TwoWire lib of Arduino in order to read a Sensor Hub Response Byte of a defined Host Command :
to...
