Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I am using nrf52832, and I want to use SYSTEM ON Sleep. Also , my wake up sourses are timer based, and also GPIO interrupt based. But I observed that the device cannot go...
Hey there!
I am currently in the process of trying to setup a simple ISR routine triggered via GPIOTE.
However, when calling nrfx_gpiote_init() or nrfx_gpiote_input_configure...
Hi together!
In my current project I would like to send some sensor data to an Azure IoT Hub, by using a nRF52840.
In the first step and for evaluation I used a nRF9151...
Problem: We have a huge variability in received RSSI (see picture) despite both devices being stationary in test setup. For our use case, accurate RSSI is critical. nRF52840...
Hello DevZone
I am currently facing an issues with device already installed at my customer. Devices are based on nRF9160, firmware based on SDK 2.8.0 and modem 1.3.6. Once...
Hi, Background For some time now I have been troubled by a bug in one of our products acting as a BLE central device. The bug manifests itself as the central reporting that...
I see that the nRF5340 is certified PSA level 2 whereas the newer nRF54L15 is certified level 1.
You claim the nRF54L15 is " designed to meet PSA Certified Level 3 ". I...
Hello Nordic support
I have encountered what I think is a bug in ICMSG. The attached sample shows the following behavior:
The first time it runs, the app and flpr CPUs...
Hello Team,
I am not able to flash any firmware to nRF5340 which is available in Thing 91x. I had tried peripheral_lbs example which was working fine. When I tried to...
Hey everyone,
I’ve been banging my head against an issue with my custom nRF54L15 board , and I’m under a bit of pressure to get five samples working. Unfortunately, the...
We are operating the 32.768 kHz low-frequency clock of the nRF52805 using the internal RC oscillator (LFRC).
We measured the LFCLK frequency of 100 devices, and the observed...
Hello, I'm trying to use the nRF54LM20A, but I'm a bit confused about the reference circuitry. What does "VDD_USB_3V3" refer to? What about all the different antenna labels...
Hello Team,
I am working with nRF52833 configured as a BLE scanner using nRF Connect SDK for VS Code .
Here is my prj.conf:
AND here is scan/conn Implementaion:
...
