I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I was reviewing the MNO certifications, and I see that there have been no updates since 1.5.1.
1) Is it acceptable to use 1.6.1 with AT&T?
2) Is certification planned...
Hi, I am trying to update the battery level through an example of the HID keyboard of nrf52832.I'm trying to connect 3.3V battery to SAADC AIN0, but as shown in the picture...
Hi, I have a question about nRF Connect Programmer tool.
[Description]
The device memory layout shows the address range as "0x00000000 - 0x00100000 (size 1048576 bytes...
Hi,
In our application, we are using HID to control mobile phone or PC.When users connected our product, it will automatically connect next time.
But our product is battery...
Hi
I am using Zephyr samples (common with the samples found in NCS) to evaluate the advertisement function of nRF52833DK.
I have run these examples:
Bluetooth: Periodic...
Hi,
After updating the FW as shown on the video, LED3 is NOT blinking, trying to connect (LTE).
If I open the terminal window, select the board, and pressing the Reset...
Hi,
We are using the GPS xample for the nRF9160. and are struggling a little with getting the GPS fix.
$GPGGA,001932.00,,,,,0,,99.99,,M,,M,,*6F $GPGLL,,,,,001932.00...
Hello to all the Nordic Jedi knights!
I have a question regarding the PPK2: Is there a way to disable auto-ranging and manually select the measurement range?
I know that...
Hey,
I have a custom board with nRF52833. Sensor is connected to: P0.11 (pin 19) - SCL P1.08 (pin 17) - SDA
with code below I don't get any `NRF_SUCCESS` back.
I saw...
I'm trying to build a new device that I bit, bang the I/O Also others to just have simple signal controls.
Below is the portion of my dts file. The example here is the onewire...
Hi,
I am using nRF52810 (s112 softdevice) with SDk version "17.0.2".
How do I set BLE advertise in continuous mode(if not connected then advertise continuously until it...
Hi
I am trying to declare a custom cluster in zigbee and enable the reporting for some attributes of the cluster, i followed this post to create the custom cluster devzone...
Hi guys,
I'm researching the maximum direct connection distance between two Android phones for transfering small amount of data - which lead me to BLE Coded PHY S8 as a...
