Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello.
I am using nrf51822/SD-130/SDK-12.3 now.
In order to preserve values after reset, no init was set in the IRAM area.
The setting area is Start: 0x20007B80...
Are there any nRF 52805 BLE examples anywhere on the net?
I have not been able to find any. Do they actually want to sell this chip? Do they like money?
Thanks!
Jam...
I am using nRF52810 with SDK 17.0.2 with UART function but I am getting error NRF_BREAKPOINT_COND. I also tried running the uart example of the SDK but the error still occurs...
Hello Nordic Team
I use SDK 15.3. I have an application that is based on ble_app_uart. It switches between uart and beacon advertisement periodically. I used pca10040_ble...
Dear Nordic Team,
i could not find a good and clean starting point for a development of a simple Open Thread application, which is not bases on CLI in the examples. Therefore...
Hi all,
I am now testing with ecdsa example with nrfutil generated key. I found that the public key generated by nrf_crypto_ecc_public_key_from_raw is not the same format...
Hi,
On new fresh delploy of cat Tracker web app, and asset tracker v2 aws without code change (i had a working version a week ago)
Now i have authentication error message...
Hello. I migrated my code from nRF5 SDK for Thread and Zigbee to nRF Connect SDK (NCS) . After that SPI code stopped working :( After debugging with the oscilloscope, I found...
Hi! I am trying to write code on MFRC522 to read data from RFID tags and write data to them, but the datasheet leaves much to be desired, and libraries are available only...
Hi,
I want to upgrate bootloader in my firmware.
IC: nRF52832
SDK: 17.02
I have finished my project, this project include boot + softdevice + app + settings,and...
Hello support team Devzone.
I am new member and i have a nRF51 DK board.
I try to create hex file for my nRF 51 DK board on the website : Mbed Compiler
when compiler...
Hello,
I'm sorry for this question, it can be easy for most of you I guess. I would like to measure the current consumption of the Thingy91, I see in the documentation...
I am running a simple cloud example where I am trying to send a CoAP GET message to coap.me:5683 server over Thread.
I can ping 64:ff9b::0808:0808 and get a response. I...
Hello I want to know what is the command that I must add to the ble_uart code which exists in the SDK library to send hello word using the bleutooth in the nrf UART application...
in \connect SDK\v1.5.0\nrf\samples\bluetooth\peripheral_uart,data number is limited 20 bytes, more than 20bytes BLE will part data in two or more packs to send or receive...
