Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello,
I'm working with the nRF9151, and I want to get useful information when a NULL pointer dereference happens, as I am used to on other devices. However, when a NULL...
I noticed that the product information of the nRF54L15 series kit supports 4Mbps, but I'm unsure how to verify it. Are there any relevant examples available? I have currently...
Hi everyone,
I am currently working with Circuit Dojo nRF9151 using nRF Connect SDK v3.0.1.
When measuring power consumption over MQTT and UDP , i noticed ~25mA every...
When I wake up from sys_poweroff using GRTC, the reset cause I get is reset_clock which is defined as clock error. I am supposed to be waking up with reset cause
RESET_LOW_POWER_WAKE...
HI,
I am using the nRF54L15 + nRF21540 with SDK v3.2.1 , and performing custom development based on the periodic_adv_conn sample.
issue Description
During runtime...
Hi,
A few months ago, I raised a ticket regarding the integration of SoftSIM into the nrf_cloud_multi_service sample. With the help of one of your support engineers, I was...
There appears to be a bug with commenting in prj.conf. If I do this:
# This is the appearance of the device from the BLE SIG Assigned Numbers List (384 is general remote...
Hi,
I'm designing a custom board with the nRF9151, nRF54L15, and nRF7000. I've read in several places that the SPI bus used by the nRF70 series should not be shared with...
Hello,
I configured the hci_uart sample for the nRF54L15 DK by following the instructions in this official Nordic documentation:
https://docs.nordicsemi.com/bundle...
I have an additional part in my design that requires a 32MHz clock input. Is there a 32MHz buffered clock output that can be configured/used from the nRF54/nPM1300 to achieve...
Hello, my product is undergoing KC certification testing. The required testing bands are LTE-M Band 3 and Band 5. However, the certification company reports that my device...
Hello,
I've got a nrf52840 DK to flash custom PCB with nrf52840 QFN. I can flash the custom PCB by using <nrfjprog> command into VSCode but the code doesn't seem to work...
Hi,
I checked the information about nRF52840 DK versions supporting Cortex-M33 devices.
In my case, I am using an nRF52840 DK, but I am facing the following behavior:...
We have a device that is using nRF9151 for LTE-M and GPS. The device has 2 versions, one with U.FL and other with chip antenna with matching network.
During testing we found...
Hi Nordic,
I'm using custom board based on nrf52840 SoC. After migrating the SDK, the original device tree configuration for ADC became unavailable, but I failed to find...
