Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi
we are using the BT HCI to add BT functionality to nrf9160 using the thingy91 hardware. upon updating the sdk from 2.7.0 to 2.8.0, we are getting the error bt_hci_core...
I want to read and write data such as incline and resistance from the Zwift app using my nrf52dk device. Based on the information I found online, it seems I need to communicate...
Hi,
My custom NRF52840 device has two interfaces (UART and USB) for host connection. I have successfully verified firmware upgrades using mcumgr from a mcuboot via the UART...
Hi
Use the following routine NRF\nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs.
Use IOS APP Enable the data to be sent once...
When evaluating BLE mesh with multiple nodes the nRF52840 Dongle is perfect to keep cost and physical size down.
I thus have one nrf52840 DK and a couple of nRF52840 Dongles...
We can get the active end points and list of cluster in end points.
But is there a way to get list of attribute and types of attribute in each cluster?
Hi community,
I read these articles about match network for antenna:
General PCB design guidelines for nRF53 series - nRF5x - Hardware design, test and measuring - Nordic...
Hi,
Like some other users, I face an issue migrating from ncs<2.6.0 to ncs 2.7.0 regarding radio notification.
I saw it is possible to use the PPI for the EGU IRQ to be...
Hello, I am using the Soft Device S140 7.3.0 with nRF5 SDK 17.1.0 and the nRF52820 as a peripheral in an NUS application. Initially, the transfer was slow but worked perfectly...
Using the nRF54L15 Development Board.
Did try to run the "nRF connect for desktop" - "Quick start"
I do not get a reply from the Board when doing one of the samples. ...
Hello!
Assume a BLE device already has Bluetooth qualification.
Does FOTA DFU requires new a Bluetooth qualification and additional fees if SoftDevice was updated too...
Hello, I am working on nrf52840 in which the BLE is not Advertising even after i am adding one paramter i just want to add the parameters at the time of adding the 2 parameters...
I am attempting to get the SMP server sample to work on some custom hardware in order to run a BLE FOTA. I'm using NCS version 2.6.1.
I'm able to build the SMP server sample...
Hi team,
I am using ncsv2.8.0, on our custom designed nrf52832 board.
Here I am trying to integrate i2c driver code for bme688 along with bsec library in peripheral_uart...
