I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
Is there a Zephyr sample project on QSPI with nRF52840? What I want to do is to write/read to an external flash (W25Q16JVSNIM).
Thank you
Best regards
Dav...
Hello,
I work on a thingy52 since few weeks with a nrf52832 SoC. When i'm turning it on and connecting it to my computer, there is no led turn on and it is not detected...
Im currently working on BLE SMP DFU on Nordic52840DK (Connect SDK v2.7.0) based on this example:
https://github.com/hellesvik-nordic/samples_for_nrf_connect_sdk/tree/main...
Hello everyone,
I am working on a project with a Thingy91 that has an nRF52840 and an nRF9160 , and I am trying to read the battery level. I want to measure this battery...
In ticket Case ID 290251, Torsten Rasmussen provides the following advice to ensure that the toolchain corresponding to the SDK is used to build the SDK (this applies to nrfutil...
I am lab testing Nordic's DECT-NR+ (DECT) for a new factory automation application; I am using the hello_dect sample application from the PHY webinar demo, I am trying to...
I made a custom board, uploaded the Arduino bootloader and was flashing the firmware with Arduino I used it without any problem with revision 2 But when I use revision 3 chip...
Hi! I'm working on the firmware part that needs to perform operations on the same variables both inside GPIO IRQ and the software timer callback. So, there is a need for a...
Hello, I want to send data from peripheral devices to central device. My peripheral device code is based on "ble_peripheral_uart" sample and my central device code is based...
Hi, I'm working on developing a UWP app that can detect any or compatible Nordic devices. let's say a device has BLE capabilities, then through the desktop app i should be...
I have both a nRF5430DK and a nRF9151DK (or 9161). If I wanted to develop a solution with both BLE and LTE, how do I set up a DK environment for them to work together? Do...
Hello,
In my experimentation to update advertising data during runtime, I am following the example @
It is using the ble_advertising.h library module
However I would...
Hi,
I am using BM840 BLE module and I see after integrating the DFU application, the main application is not executing at all.
When I try to debug, I see it is not coming...
Dear Nordic Semiconductor Support Team,
I am conducting academic research with the nRF52840 development board, specifically investigating the use of SRAM Physical Unclonable...
HI Sir/Madam
I downloaded SUPL-C sdk 0.7.2 ad I add the following variable to the prj.conf
#SUPL client library
CONFIG_SUPL_CLIENT_LIB =y
CONFIG_GNSS_SAMPLE_ASSISTANCE_SUPL...
