I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I get this error when I try `nrfutil device list`, and any other nrfutil device command.
However, if I use `nrfutil device --jlink-dll /path/to/libjlinkarm.so...
Hello,
My name is Jeon. I am using the RTC function on a custom board that utilizes the same chipset as the nRF9151. I have configured the RTC to trigger an alarm every...
Hello,
I need to make the OTA DFU work and I followed the instructions here: https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/samples/subsys/mgmt/mcumgr/smp_svr...
Hi,
Please note that we are having below setup
Module: nRF52832 based HolyIoT YJ-16048 Module SDK: NRF 17.0.2 Tools: Power Profiler Kit II
Expected current consumption...
Greetings,
Does anyone know if there are updates planned for the Arduino IDE with the latest SoftDevice versions? I opened this issue on GitHub: https://github.com/sandeepmistry...
I am using NCS 3.0.2 + VSCode to develop for the nRF54L15 . I have two projects:
\nrf\samples\bootloader\src
\nrf\samples\esb_prx
Since my custom board...
The instructions for running the sample are too difficult to follow. Here is why/where:
>>The sample also requires a device running a CTS Server to connect with (for example...
I am using nrf 52840dk board i need to know how to reset the devlopment using software reset when we press the Button 1 in the nrf 52840dk board
1. Give some software reset...
Hello,
I want to Configure a UART RX pin as GPIO and use it as a Wake - up interrupt pin before going to sleep. Is this possible in nrf54l15?
I tried to do so, but I was...
I've been having problems getting nRF Connect to flash a target through my J-Link programmer lately, even though it has historically worked fine. I suspected the issue might...
Hello, I want to flash a test application to the nrf52820(on the 52833DK(it supports both 33 and 20) for test purposes. I first flashed the softdevice and the bootloader....
Hello everyone,
I've noticed that when using MCUBoot+External Flash+OpenThread+FOTA over BLE+PWM, the program startup time is extremely long, reaching 1684 milliseconds...
When calling the bt_conn_le_create_synced function to create a connection to a peripheral, which is synced to the PAwR train, I get a CONNECTION FAILED TO BE ESTABLISHED ...
Now we have bound the corresponding pins in the device tree, and there is no pin multiplexing except for LED and BUTTON. However, now as long as we configure SPI in the main...
