hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I just move code from main.c to other files for it is too chaos to lay them together in main.c.
I got this error forever after trying what I can image,except delete "static...
Prior to moving to sysbuild, we were dynamically settings a CONFIG_ variable in our `CMakeLists.txt` based on the board passed to west. And this was working fine.
if...
I've had trouble getting the MCUboot to compile for our application which runs on the nRF7002DK board, and I have similar trouble with the Lesson 8 examples on the nRF7002DK...
I have searched this website,there is only 1 post,but that is not my scenario.
I think this is a normal use case:
There is a struct:
I want to allocate a queue for...
Hi!
I have a bootloader using SPI 3 for a bootloader LCD animation. Unless I attach an RTT console, the animation causes my DFU to fail 100% of the time. It is making me...
Hi,
Since I want to flash the factory data later, I don't want to use the default certificate. I set CONFIG_CHIP_FACTORY_DATA_BUILD to n in prj_release.conf , but a compilation...
Hi Sir, We are planning for a Hardware deign by using nRF52833 and we are stuck on what should be suitable the supply voltage. In some case the data sheet showing that it...
Hi there,
I'm encountering an issue while trying to flash a PWM example built with NCS v2.9.0 on Windows 11 (using Python 3.10 ). The build completes successfully and generates...
I have a collection of nRF9151 devices using PSM mode.
Each time the application attempts to send UDP data while in sleep mode, they get a detach request (from the network...
Hi
I have two nRF52833 development boards: one is using BLE peripheral_uart, and the other is used as RX (BLE central_uart). My issue is that, with the TX setup being completely...
When a button is pressed during power off, the buttons module disables the wakeup interrupt but the button scan never happens, leaving the module in an invalid state and preventing...
Dear Nordic support,
I was reading the Technical Documentation in the GPIO section for the nRF9151 , and I came across this blurb:
"Note: When a pin is configured as digital...
nrf5340 - running the complete BLE advertising and handling the read / write gatt client processing running in network core and doing rpc to application core
Create a sample...
Hi
I have questions about nPM1300 VOUT1 inductor
1. Our load current for VOUT1 will be <20mA, so could we use below inductor?
2. Datasheet 6.3.5 define it's recommended...
