I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello, I am using nRF52 DK and SDK V15.2.0 with a Nordic PPK to measure current draw. I have read tons and tons of questions posted here but am still unable to figure out...
Hi all :) ,
I'm trying to create my new zip folder with new image.
I connect to my nrf52833, then i click on dfu button into nrfConnect mobil app.
I selec zip file...
I'm using:
OS : Windows 10
IDE : Segger Embedded Studio for ARM Realease 4.52c Windows x64
SDK : nRF_SDK_15.0.0_a53641a
In my project I'm using 4 pressure sensors...
Hi,
I've been trying to make a small modification on the existing Nordic Thingy firmware, such as changing the color of an LED, by compiling the existing Nordic Thingy 52...
Hi,
I am trying to set up a region of RAM to store variables that persist across soft reboots but am unsure how to do it in this environment. I would normally define a region...
Hi Nordic ppl,
Is Nordic SoC supporting BlueZ package ?
Any specific SoC that we should be selecting to be able to run the .
Also, i believe all 3rd party Modules...
I am trying to implement openthread cli uart in pca10059, have made all modifications but the hex file is not getting burnt in bootloader mode using nrfconnect
/cfs-file...
Hi:
I use the PCA1004 EVK bord to configuer the I2S MCK as 256K, 32MHz/125 (I2S_CONFIG_MCK_SETUP 34340864) .
then I measure the pin use oscilloscope, but I only get 255K...
Hi Nordic support,
We had an "intermittent" connection failure with a BLE radio in one of our products under development, which exhibited itself with an <unknown> device...
Hello,
We want to use the flash to store two types of information: application configuration settings (which should be protected during DFU) and temporary data (which...
Hi,
I m using nrf52840 and m doing DFU over serial.
one side is master controller and other end is NRF DFU serial(secure bootloader uart debug code).
After sending init...
Hi everyone,
I am trying to connect to a smartphone in an extended advertising using the firmware created under the following conditions. However, there are no event notifications...
Hi.
Development platform : nRF52833-DK, s113, SDK 16.0.0, IAR 8.31.1
I am making an example of periodically reading sensor data using SPI.
The SPI is triggered through...
Currently I am using a PCA10040 to do some prototyping for a custom board. I intended to use the nrf52832 to interface with a HDC2010 (TI) temperature and humidity IC over...
