Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello,
My problem is that i have seen a reduction in throughput with android oreo in a huawei p10. Before the update i was able to send two notification per connection interval...
I use PCA10040 development board. COM port suddenly stopped working. The issue is visible also in Device Manager:
Google suggests that this issue is caused by Windows...
Hi
We have project where we want to use a nrf52 in an remote keypad for control various devices.
For investigating the capabilities I have tested the ble_uart and ble_blinky...
Hi,
I've been working on a project where I need to send data from UART over mesh, I managed to create custom model for sending string data over mesh, I did merge UART example...
Hello. I have SMARTMP3 Board and NRF52832. The vs1053 works fine on the arduino. But it doesn't work on the nrf52832. I use these connections: #define SCK_PIN 3 #define MOSI_PIN...
The NRF52840 appears to only come in a dual row QFN package and in the reference material, the only way to break out the second row is with an in-pad via or a very small trace...
Hi I am trying to use a different base UUID template than 0 x ABCDxxxx-1212-EFDE-1523-785FEABCD123.
For my services I would like to use 0 x xxxxABCD-1212-EFDE-1523-785FEABCD123...
From what I understand the clock source for the example ble_app_uart is the 32 KHz external crystal. Please, see the screenshot of the CMSIS configurator:
How do I set...
Hi all!
I use the ACM_CDC USB class to transfer a batch of data (150MB) from the MCU (nrf52840) to the host. Currently, the system reaches up to 100KB/s upload speed, although...
Hi @ll, I have the following problem: There are three unprovisioned devices with UUIDs containing a 0x0A byte but the scanner within the pyaci script shows 0x00 instead. Device...
Hi.
To avoid via in PAD I like to route a signal/pin from the inner row (closest to center) through a pin in the outer row.
However, to be able to do that I must be sure...
We are using SDK_13.0.0_04a0bfd and want to change the location and size of the bootloader in flash. But when we do this, the bonding process in the main application doesn...
I'm a newbie to nRF5... I just installed latest IAR, nRFgo, Segger J-link & nRF Connect on Windows-10. Segger J-link appears to have updated nRF51 Dongle to 6.3. I get the...
I'm developing firmware for a client that includes a connectable beacon. I'm using code based on a Nordic example, though I can no longer find the original. I'm trying to...
